Answered: PROBLEM 2: A TRICKY STRUT An orange… | bartleby

Related questions

Question

PRO BLEM 2: A TRICKY STRUT
An orange strut of length l is connected to a wall via a
pi vot at the bottom. An additional (blue rope) also connec ts
the strut to the wall attached at an angle 01. A load of weight
W is hanging from the strut; the load makes an angle 02 with
the strut as shown in the diagram. In order to stabilize the
system, and additional force needs to be applied. That force,
which is labeled C in the diagram, makes an angle p with
respect to the strut as shown. What is o?

Expert Solution

Step 1

Consider the following diagram,

Step 2

Now applying the equilibrium conditions.

From the above figure,

$\begin{array}{rcl} T \sin θ_{1} d & = & W \sin θ_{2} d \\ T & = & \frac{\sin θ_{2}}{\sin θ_{1}} W . . . . . . . . . . . . . . . . . . . (1) \end{array}$

Step by step

Solved in 4 steps with 1 images

Blurred answer

Similar questions

After an unfortunate accident occurred at local warehouse you were contracted to determine the cause jib crane collapsed and injured worker: An image of this type of crane is shown in the figure. The horizontal steel beam had mass of 85.10 kg per meter of length; and the tension in the cable was T = 11650 N. The crane was rated for a maximum load of 500 kg: The acceleration due to gravity is g=9.810 m/s2 lf d= 5.290 m, S = 0.558 m_ X=1.200 m and h =1.890 m_ what was the magnitude of W L (the load on the crane) before the collapse? What was the magnitude of force Fp at the attachment point P?
You are on a pirate ship and being forced to walk the plank (Figure 1). You are standing at the point marked C. The plank is nailed onto the deck at point A, and rests on the support 0.75 m away from A. The center of mass of the uniform plank is located at point B. Your mass is 85 kg and the mass of the plank is 45 kg. Part A What is the minimum downward force the nails must exert on the plank to hold it in place? Express your answer to two significant figures and include the appropriate units. |Fnails|= for Part A for Part Vndo for Part redo for Part A ret for Part A keyboard shortcuts Value Units
Part A End A of the bar AB in (Figure 1) rests on a frictionless horizontal surface, and end B is hinged. A horizontal force F of magnitude 270 N is exerted on end A. Ignore the weight of the bar. What is the horizontal component of the force exerted by the bar on the hinge at B? Express your answer with the appropriate units. HẢ ? Fh = Value Units Submit Request Answer Part B What is the vertical component of the force exerted by the bar on the hinge at B? Express your answer with the appropriate units. HÅ ? F, = Value Units Submit Request Answer Figure 1 of 1 Provide Feedback Next > 5.00 m 4.00 m A B.
Q3: determine shear stress (t) for each 16-mm diameter bolt. 40 kN 40 kN 30 mm 80 kN 30 mm
Determine whether the 15-kg block shown is in static equilibrium under the loadings shown, and report the magnitude of the friction force (in Newton) when P = 700 N and 0 = 47 degrees at the state of static equilibrium. The coefficients of static and kinetic friction between the block and the rough inclined surface are shown in the picture. Report the friction force as positive when it is directed downward, and negative when it is directed upwards. 500 N Hs=0.35 Mk = 0.25 35° Ꮎ
Please answer all the question in the given problem. Kindly show clear and complete solutions. Thank you
6 Determine the support reactions and all member forces for the truss below. Note that BD does not connect to, but bypasses, member AC.