9-17. The bar has a length L and eross-sectional area A. Determine its elongation due to the force P and its own weight. The materialhas a specific weight y (weight/volume) and a modulus of elasticity E.

Q: The way to the column where the loading status is seen determine the P load required for the 5 mm…

A: Given that,

Q: he forklift supports the engine. Determine the force that generates this load on element DB. Write…

A: Given data as per question Engine mass = 114 kg =1118.34 N a = 1.47 m b = 1.81 m Considering FBD of…

Q: 4-35 Deter mine compressive logds in members AB and BC. FBD of B BC AB=160 AB/I5 160lb AB = 3401bin…

A:

Q: If the force P equals 2500 lbs. Determine the maximum tensile stress in the section of the hook…

A:

Q: The two bars are made of a material that has the stress-strain diagram shown. If the cross-sectional…

A: Given data as per question  Cross-sectional area of AB =1.5 in2  Cross-sectional area of Bc=4 in2

Q: Determine the strain energy in the bar assembly. The portion AB is made of steel, part BC is made of…

A: Length of steel portion ,LAB=300  mmLength of Brass portion, LBC=400 mmLength of aluminium portion…

Q: K 3m * 3m * P D 6m B E 6m 9m The truss ABCDEF is pinned at A and F. What is the force in bar BE when…

A: Step 1: Analyse the diagram Step 2: Proceed step by step. Step 3: Take equilibrium Equations…

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

A: For aluminum rod,For steel rod,The displacement towards A  to left is,

Q: A 300kg counterweight with center of mass at G is mounted on the AB crank rod of the oil pump unit.…

A: Given Data Torque supplied by motor is : M=250 Nm  Mass of the counter weight mounted on crank AB…

Q: The 460-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

A:

Q: 3.5 m r= 0.6e-0.08y² y 0.6 m

A:

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: 1- For the tapered bar shown with cross sectional areas A-0.02 m² and A 0.01 m² at each end. The bar…

A: In the question load is 4500N but in the diagram given load is 4000N , So I am solving with 4000…

Q: Step 3: Consider section at distance X2 from point B and free body diagram of section shown below.…

A:

Q: If the temperature of the 85 mmmm diameter post CD is increased by 60 ⚫C, determine the force…

A:

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

A: For aluminum rod,For steel rod,The displacement towards A  to left is,

Q: The bar is made of aluminum alloy 2014-T6. Determine its thickness b if its width is 1.5b. Assume…

A: Given data: The width of the bar, b = 1.5b. The length of bar, L = 5 ft. The applied load, P = 800…

Q: The bar is connected to the support using a pin having a diameter of d =lin. If the allowable…

A:

Q: If the yield strength for the bar is Gyield = 220 MPa, determine the maximum axial force P that can…

A:

Q: 16-6. Determine the support reactions at pins and 3. Take E = 200 GPa, I = 350(10) mm, A = 15(10³)…

A: Determine the support reactions at pins 1 and 2. Take E 200 GPa, I = 350(106 ) mm4 , A = 15(103 )…

Q: 1-103. The bar is supported by the pin. If the allowable tensile stress for the bar is (o)allow =…

A: