**80. mmh By means of a rope whose mass is neg- ligible, two blocks are suspended over a pulley, as the drawing shows. The pulley can be treated as a uniform solid cylindrical disk. The downward acceleration of the 44.0-kg block is observed to be exactly one-half the acceleration due to grav- ity. Noting that the tension in the rope is not the same on each side of the pulley, find the mass of the pulley. 11.0 kg 44.0 kg Problem 80

**80. mmh By means of a rope whose mass is neg- ligible, two blocks are suspended over a pulley, as the drawing shows. The pulley can be treated as a uniform solid cylindrical disk. The downward acceleration of the 44.0-kg block is observed to be exactly one-half the acceleration due to grav- ity. Noting that the tension in the rope is not the same on each side of the pulley, find the mass of the pulley. 11.0 kg 44.0 kg Problem 80

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

In the figure below, block 2 of mass m2 = 3.75 kg rests on a frictionless surface. It is attached to mass 1 (m1 = 2.50 kg) by a massless, stretchless string that passes over a frictionless pulley of radius R = 15.0 cm. When released from rest, block 2 moves to the right with an acceleration of 3.80 m/s2. What is the mass of the pulley? must draw FBDs
Two blocks are connected to a rope, and the rope is hung over a pulley connected to the ceiling, as shown in the figure below. 1721 Mo i The masses of the blocks are m₁ = 16.0 kg and m₂ = 11.5 kg, the mass of the pulley is M = 5.00 kg, and the radius of the pulley is R = 0.100 m. Block m₂ is initially on the floor, and block m₁ is initially 4.20 m above the floor when it is released from rest. The pulley's axis has negligible friction. The mass of the rope is small enough to be ignored, and the rope does not slip on the pulley, nor does it stretch. (a) How much time (in s) does it take block m, to hit the floor after being released? At₁ S (b) How would your answer to part (a) change if the mass of the pulley were neglected? (Enter the time, in seconds, it takes block m, to hit the floor if the mass of the pulley were neglected.) At₂
A thin cord is wrapped around a uniform grindstone of radius 0.30 m and mass of 25 kg supported by bearings that produce negligible friction torque. The cord exerts a steady tension force on the grindstone, causing it to accelerate from rest to 60 rad/s in 12 s. (lgrindstone = 5 What is the magnitude of the tension force of the cord? O 5.6 N 11.3 N O 18.7 N O 37.5 N
help asap
Two blocks are connected to a string, and the string is hung over a pulley connected to the ceiling, as shown in the figure below. MG R m1 m2 The masses of the blocks are m, = 17.0 kg and m, = 10.5 kg, the mass of the pulley is M = 5.00 kg, and the radius of the pulley is R = 0.100 m. Block m, is initially on the floor, and block m1 is initially 5.00 m above the floor when it is released from rest. The pulley's axis has negligible friction. The mass of the string is small enough to be ignored, and the string does not slip on the pulley, nor does it stretch. (a) How much time (in s) does it take block m, to hit the floor after being released? At, = (b) How would your answer to part (a) change if the mass of the pulley were neglected? (Enter the time, in seconds, it takes block m, to hit the floor if the mass of the pulley were neglected.) At,
Suppose we want to calculate the moment of inertia of a 65.5 kg skater, relative to a vertical axis through their center of mass. a. First calculate the moment of inertia (in kg⋅m2) when the skater has their arms pulled inward by assuming they are cylinder of radius 0.125 m. b. Now calculate the moment of inertia of the skater (in kg⋅m2) with their arms extended by assuming that each arm is 5% of the mass of their body. Assume the body is a cylinder of the same size, and the arms are 0.875 m long rods extending straight out from the center of their body being rotated at the ends.
A uniform hollow spherical ball of mass 2.14 kg and radius 0.56 m rolls without slipping up a ramp that rises at 30.0° above the horizontal. The speed of the ball at the base of the ramp is 3.42 m.s1. While the ball is moving up the ramp, find (a) the magnitude of the acceleration of its center of mass. m.s2 (b) the magnitude of the friction force acting on it due to the surface of the ramp. N
The block on a smooth inclined plane is moving down with a constant acceleration of 4 m/s². m. m o W The block on the inclined plane is 35 kg and the hanging mass is 24 kg. The radius of the pulley is 0.33 m. The angle theta is 56 degress. Determine the moment of inertia of the pulley. ROUND OFF FINAL ASWER UP TO 2 DECIMAL PLACES. INPUT THE NUMBER ONLY.
A 4.00-m-long, 500 kg steel beam extends horizontally from the point where it has been bolted to the framework of a new building under construction. A 70.0 kg construction worker stands at the far end of the beam. What is the magnitude of the gravitational torque about the point where the beam is bolted into place?
In the arrangement shown in the figure, we want to calculate the acceleration of the system If we have that m1 = 50.8 grams and m2 = 127.4 grams, neglecting the friction in the pulley and its moment of inertia, we will have that the theoretical acceleration of the system will be: Select one:to. 7.01b. 4.21c. 2.79d. None is correctand. 3.91