8.31 • An ice hockey forward with mass 70.0 kg is skating due north with a speed of 5.5 m/s. As the forward approaches the net for a slap shot, a defensive player (mass 110 kg) skates toward him in order to apply a body-check. The defensive player is traveling south at 4.0 m/s just before they collide. If the two players become intertwined and move together after they collide, in what direction and at what speed do they move after the collision? Friction between the two players and the ice can be neglected.

8.31 • An ice hockey forward with mass 70.0 kg is skating due north with a speed of 5.5 m/s. As the forward approaches the net for a slap shot, a defensive player (mass 110 kg) skates toward him in order to apply a body-check. The defensive player is traveling south at 4.0 m/s just before they collide. If the two players become intertwined and move together after they collide, in what direction and at what speed do they move after the collision? Friction between the two players and the ice can be neglected.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q⁴
please help me with this question i got someone else to help me and they got the wrong answer now i only have one attempt please help me get the right answer thank you
5. The gas tank (inner diameter 1.5 m) is made from steel which has a yield strength of 250 MPa. If the tank is designed to withstand a pressure of 5 MPa with a safety factor of 1.5, determine the required minimum thickness to the nearest millimeter using a) Tresca's yield criterion b) Von Mises' yield criterion.
Select All Correct Answers.
Does the location of the shear center depend upon the applied loading?
16cm. 34.8cm = 1.0 SGcone = 0.9 Which is the more stable pesiton? IS
1.4 (A). Twe fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they are required to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of either fork if the stress in the fork material is not to exceed 180 MN/m2. What wili be the maximum shear stress in the pin' [1.39 x 10-m'; 50.9 MN/m] 1.5 (A) A simple turabuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally at each end to take two rods of 25 man outside diameteT with threaded cnds. What will be the nominal stresscs set up in the tube and the rods, ignoring thread depth, when the turabuckle carries an axial load of 30 kN? Assuming a suficient strength of thread, what maximum load can be transmitted by the turnbuckle if the maximum stress is imited to 180 MN/m? [39.2, 61.1 MN/m2, 88.4 kN.]
QUESTION 4) For the given plane state stress, if the components at the inclined surface is known and the normal stress is known to be zero about the +ty direction, calculate the stresses that will occur in the 14 MPa MPa plane where the direction of the normal axis is x, and show all an oriented element. 30
Answer all the points, please
1) Show that the APF for BCC = 0.68 Subject:FUNDAMENTALS OF MATERIAL SCIENCE AND ENGINEERING
The ratio, when a sample object is stretched, of the contraction or transverse strain (normal to the applied load) to the extension or axial strain (in the direction of the applied load) is referred to as O Answer not in the choices O Transverse-to-axial strain ratio O Puzon's ratio O Poisson's ratio O Dilatation ratio
A strain gauge is used to measure the shear strain on a shaft during torsional loading. The strain gauge is mounted such that it measures strain at an angle of 45° to the longitudinal axis of the shaft. The shear strain in the shaft is determined: a. as the strain measured by the strain gauge O b. by dividing the strain measured by the strain gauge by the shear modulus O c. None of these options O d. as twice the normal strain determined by the strain gauge.