Please don't provide handwritten solution ..... !Required InformationConsider the given state of stress. Given: X= 40 MPa and Y=70 MPa.25 MPaXDetermine the principal planes using Mohr's circle.andThe principal planes are atShow Transcribed Textand can you alsob) Determine the principal stresses using Mohr's circle.c) the orientation of the planes of maximum in-plane shearing stressd) the maximum in-plane shearing stresse) the corresponding normal stress.

Solution:The average stress is given by,The centre point 'O' of the Mohr's circle is, (15, 0).The…

Required Information Consider the given state of stress. Given: X= 40 MPa and Y=70 MPa. 25 MPa X Determine the principal planes using Mohr's circle. The principal planes are at - [ and Show Transcribed Text and can you also b) Determine the principal stresses using Mohr's circle. c) the orientation of the planes of maximum in-plane shearing stress d) the maximum in-plane shearing stress e) the corresponding normal stress.

Required Information Consider the given state of stress. Given: X= 40 MPa and Y=70 MPa. 25 MPa X Determine the principal planes using Mohr's circle. The principal planes are at - [ and Show Transcribed Text and can you also b) Determine the principal stresses using Mohr's circle. c) the orientation of the planes of maximum in-plane shearing stress d) the maximum in-plane shearing stress e) the corresponding normal stress.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2) The state of stesss at a point in a body relative to the xyz coordinate system is: 2 3 -5 [o]= 3 2 kpsi 6. %3D -5 2 -4 a) Determine the principle stresses and the direction cosines corresponding to each principle stress. b) Draw the 3D Mohr's circles. c) Determine the maximum shear stress. d) Find the orientation of the plane containing the maximum shear stress relative to the original axis system 3) For the stress tensor in problem 2: a) Determine the normal and shear stress on a surface intersecting a plane defined by 3 points (0,0,0); (2,-1,3); (-2,0,1) b) Give the magnitudes of these stresses and the direction cosines defining their directions.
The state of stress shown to the left was produced by a combination of loadings on a body that is not shown. Determine the following via Mohr's circle: A) Draw Mohr's Circle for the x-y plane. B) Determine the principal stresses - All 3. C) Sketch a properly oriented differential element showing the principal stresses in the x-y plane. D) Determine the magnitude of the maximum shear stress in the x-y plane. E) Sketch a properly oriented differential element showing the maximum shear stress state in the x-y plane. F) Determine the magnitude of the absolute maximum shear stress (and include the two out of plane circles on your original figure). Use the following values for the magnitudes of the stresses: x = 0₂ Txy Ox X X 10 ksi, σy = 4 ksi, σ₂ = 3 ksi, Txy = 4 ksi
A plane stress state is given as follows (50MP in the bottom right corner denotes the shear component, and others denote the normal components). 1) Please draw the Mohr's circle of this plane stress state. Indicate the center of the circle, the radius of the circle, and the point that corresponds to x-plane (the normal of the plane is x axis) 2) Determine the principal stresses and directions of this stress state using Mohr's circle. 3) Draw the stress element to show maximum shear stress 71, T2, and the corresponding normal stress. 75 MPa 50 MPa 50 MPa
For the state of plane stress, stress components are shown on the element in Figure Question 1: a) Draw Mohr's circle b) Determine the principal planes and the principal stresses c) The stress components exerted on the element obtained by rotating the given element counterclockwise through 30°. y| 60 MPa x 100 MPa 48 MPa
Direct stresses of 160N/mm tensile and 120 N/mm compressive exist on two perpendicular planes at a certain point in a body. They are also accompanied by shear stresses on the planes. The greatest principal stress at the point due to these is 200 N/mm?. a) What must be the magnitude of the shearing stresses on the two planes? b) What will be the maximum shearing stress at the point?
For the given state of stress of element A, strictly using Mohr's Circle perform the following: plane 1 1 plane 2 6 =40 MPa 30° plane 3 30° -20/3 МРа T=40 MPa plane 4 ...18.435° a) Draw its MOHRS circle b) Determine the principal stresses Op1= Op2= Op3= c) Determine the maximum shear stress Tmax= d) Determine the stresses on the horizontal & vertical planes OH= Oy= THV=
The Mohr's circle representing a given state of stress is shown. The diagonal line AB represents the original orientation where point A corresponds to the x face and point B corresponds to the y face. a) Show the stresses represented by line AB on the provided stress element. 60 X -30-1 {MPa} y T(MPa) b) Determine the principal stresses and show them on a properly oriented stress A element. y X 40 B 20p 30 40 40
A force Q of magnitude 9 kips is applied to the machine element AB as shown. The uniform thickness of the element is 0.8 in. a) Determine the normal and shearing stresses at point a. b) Determine the normal and shearing stresses at point b. c) Determine the normal and shearing stresses at point c.
The plate has a thickness of 20 mm and the force P = 3 kN acts along the centerline of this thickness such that d = 150 mm. A) Determine the normal stress at the bottom edge of the plate Enter negative value in the case of compression and positive value in the case of tension. B)Determine the normal stress at the top edge of the plate. Enter negative value in the case of compression and positive value in the case of tension. C)Specify the location of the neutral axis measured from the bottom edge of the plate.
This my id 201901782
None
Please help. Do not just guess. Prove your answer. I will give a good feedback. thank you :)