8.3-8.6. Determine the equilibrium configurations of the rigid bars shown below using the principle of virtual displacements. In cach case, neglect friction and assume that each bar is of weight Q. Fig. P8.3 Fia. Pa4 Only question 9.19 should solve 9.17-9.20. Solve Probs. 8.3-8.6 using the principle of minimum potential energy instead of the principle of virtual displacements. Compare and discuss the procedures used in applying both principles to these problems.

8.3-8.6. Determine the equilibrium configurations of the rigid bars shown below using the principle of virtual displacements. In cach case, neglect friction and assume that each bar is of weight Q. Fig. P8.3 Fia. Pa4 Only question 9.19 should solve 9.17-9.20. Solve Probs. 8.3-8.6 using the principle of minimum potential energy instead of the principle of virtual displacements. Compare and discuss the procedures used in applying both principles to these problems.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 9.2 A 1200 kg mass is hanging from a small pulley that is free to roll on the cable (frictionless, of course). The length of the cable BC is 18 m. Determine the horizontal force (i.e., P) that would hold the pulley in equilibrium in the position at x = 5 m. Use COLM principles to solve. You must draw a KD and a FBD for this closed, steady state (i.e., equilibrium) system. Hint: Use LBC and geometry to find the angles of AB and BC (relative to Pulley B). 2 m T 16 m- 1200 kg Ans: 1400 N ≤ P ≤ 1700 N
Q3)) A uniform bar AB, 12 m long and weighing 250 N , is hinged at B and rest upon a 400 N as shown in the Fig. below if the coefficient of friction 4 (u ) is 0.35 between contact surfaces, find the horizontal force P required to A start block moving.
A straight, uniform bar weighing 60lb rests in a horizontal positon between two frictionless slopes. A concentrated load of 200lb acts at distance x from the right hand slope. Determine x and reaction forces assuming that the bar is in static equilibrium.
The 60 kg uniform vertical bar AB of length 2.4 m, is hinged to two massless parallel rods AC and BD, each is 1,2 m long. Bar AB is at rest when 0- 0, and AC is horizontal. A constant counterclockwise moment M-1200 N.m is applied to AC. Answer the follow ing at the instant 0 - 30°. 0.6 m 1.2m 18 m The normal inertia force action on AB The tangential inertia force action on AB= 1.2m The magnitude of the reaction force at B The magnitude of the reaction force at A=
Bar AB of Fig. with weight W and length L has a uniform cross section. Rotation of the bar is resisted by a torsional spring with spring constant 4. The spring is neutral when 0- 0°. Determine The minimum stiffness & for the spring, in terms of W and L, if the bar is to be in stable equilibrium when 0 = 0°.
The spring in Fig. is unstretched when e = 6 = 15°. Find the angle 6 for equilibrium if mg = 60 kg, mp = 25 kg, L=1 m, and & - 750 N/m. Assume that the masses of the bars are negligible. D mp
The traffic light shown in (Figure 1) has a mass of21 kg . Take h= 3.5 mm.
A homogeneous, triangular block of weight W has height h and base width b as shown in Fig. an expression for the coefficient of friction between the block and the surface for which impending motion by slip- ping and tipping occur simultaneously if Develop Force P acts in the direction shown on the figure. 9.
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 17i - 11j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. %3D 2 m 4 m 6 m A Answer: Calculate the magnitude of the tension in cable BD in kN. 3 m 6m
%£9 l. 4G 11:9 1st class / 2021- 2022 PROBLEMS 1- A ( 200 N) weight of the block shown in fig. is supported by a pin and bracket at ( A ) and by a cable (BC ). Determine the reaction at ( A ) and the tension 30 in the cable 0.75 a 2 - The 200-N force produces a torque (moment) of 40 N.m about the axis of the bolt in order to tighten the hexagonal nut . Find the forces 2mm between the smooth jaws of the wrench and the nut if contact occurs at the corners A and B of the hexagon. 3 - The pin at A can support a maximum force of 3.2 KN . What is the coresponding maximum load L which can be supported by the bracket ? 4 - A block placed under the head , of the claw hammer as shown greatly facilitates the extraction of the nail. If the 200-N pull on the handle is required to pull the nail calculate the tension T in the nail and the magnitude A ne me of the force exerted by the hammer head on the block The contacting surfaces at A are sufficiently rough to prevent slipping Alamarah University…
A sliding block weighing 50 lb can slide freely within the frictionless slot shown. The spring is undeformed (i.e., not stretched) when it is in a horizontal position. What is the spring constant k if the slider is in equilibrium in the position shown? Show your calculations and result.
%£9 lI. 4G 11:9 1st class / 2021- 2022 PROBLEMS 1 - A ( 200 N ) weight of the block shown in fig. is supported by a pin and bracket at ( A ) and by a cable ( BC ). Determine the reaction at ( A ) and the tension 30 in the cable 0.75 2 - The 200-N force produces a torque (moment) of 40 N.m about the axis of the bolt in order to tighten the hexagonal nut. Find the forces between the smooth jaws of the wrench and the nut if contact occurs at the corners A and B of the hexagon. 3 - The pin at A can support a maximum force of 3.2 KN . What is the coresponding maximum load L which can be supported by the bracket ? 4 - A block placed under the head, of the claw hammer as shown greatly facilitates the extraction of the nail. If the 200-N pull on the handle is required to pull the nail calculate the tension T in the nail and the magnitude A of the force exerted by the hammer head on the block The contacting surfaces at A are sufficiently rough to prevent slipping Alamarah University College…