8-6 The open-ended polyvinyl chloride pipe has an innerdiameter of 4 in. and thickness of 0.2 in. If it carries flowingwater at 60 psi pressure, determine the state of stress in thewalls of the pipe.

To determine the state of stress in the walls of the polyvinyl chloride (PVC) pipe, we can use the…

Answered: 8-6 The open-ended polyvinyl chloride…

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter3: The Structure Of Real Materials

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
using Figure 5-27, what is the advantage of the suspended type magnet over the other two types of magnets?
In concrete work, Fuller and Thompson (1907) suggested that a dense packing of grains can be achieved if the percent finer (p) and grain size (D) are related by the following equation, where n is a constant varying in the range of 0.3-0.6. Dmax is the size of the largest grain within the soil. p=(DDmax)n100 This equation is sometimes used in roadwork for selecting the aggregates. a. For n = 0.5, show that the soil is well graded. b. If n = 0.5 and Dmax = 19.0 mm, find the percentages of gravel, sand, and fines within the soil. Use the Unified Soil Classification System.
Why is it so difficult to process MSW?
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.

Recommended textbooks for you

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Engineering Fundamentals: An Introduction to Engi…

Civil Engineering

ISBN:

9781305084766

Author:

Saeed Moaveni

Publisher:

Cengage Learning

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Engineering Fundamentals: An Introduction to Engi…

Civil Engineering

ISBN:

9781305084766

Author:

Saeed Moaveni

Publisher:

Cengage Learning

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

Fundamentals of Geotechnical Engineering (MindTap…

Civil Engineering

ISBN:

9781305635180

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

SEE MORE TEXTBOOKS

8-6 The open-ended polyvinyl chloride pipe has an inner diameter of 4 in. and thickness of 0.2 in. If it carries flowing water at 60 psi pressure, determine the state of stress in the walls of the pipe.