8-23. The plug has a diameter of 30 mm and fits within arigid sleeve having an inner diameter of 32 mm. Both theplug and the sleeve are 50 mm long. Determine the axialpressure p that must be applied to the top of the plug tocause it to contact the sides of the sleeve. Alsa, how far mustthe plug be compressed downward in order to do this? Theplug is made from a material for which E-5 MPa, v -0.45.

Given: The diameter of the plug is dp=30 mm=0.03 m. The diameter of the sleeve is ds=32 mm=0.032 m.…

Answered: 8-23. The plug has a diameter of 30 mm…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 0.35-inch-diameter cylinder is made from C83400 red brass and is placed in the device depicted below when temperature is T1 = 5 oF throughout. The two Am 1004-T-61 magnesium alloy carriage bolts each have a diameter of 0.10 inches and hold the cylinder snug with negligible force against the rigid jaws. Determine the maximum temperature (in oF) that the brass cylinder can be subjected to without causing yielding of any one of the materials. The end plates will not deform or fail.
A thick-walled cylindrical pressure vessel with an inside diameter of 280 mm and an outside diameter of 430 mm is made of a steel that has a yield strength of 420 MPa. Determine the maximum internal pressure that may be applied to the vessel if a factor of safety of 3.3 with respect to failure by yielding is required. Part 1 Determine the maximum allowable tensile stress in the vessel wall. Answer: Oallow i MPa
The rod BD is made of materia with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2=1042 N.m, answer the following questions: A B T2 N-m 0.4 m 0.1 m 0.3 m T1 N-m The angle of twist at D is The angle of twist between C and B is The reaction at point A is
1. The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied to it, determine the change in its length and the change in its diameter. Material parameters are Ep = 2.70 GPa and vp = 0.4. 300 N 200 mm 300 N
can you help answer this question please? thank you.
If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of P. The wire is A-36 steel and has a diameter of 3 mm.
Please provide step-by-step calculations, also draw the nodes showing temperatures l A rectangular cross-section bar is held in steady conditions at different temperatures on each of its 4 sides. There is no internal heat generation, and the material properties are constant in all directions at all temperatures. The cross section has an aspect ratio of 1.5, with its longest side measuring 2.5 m in the x direction. It is split into 4 nodes in the x direction and 3 nodes in the y direction. The node numbering starts from (1,1) in the bottom left hand corner. The temperatures of the faces are held constant as follows: left hand side = 428 K, right hand side = 506 K, top side = 367 K, and bottom side = 298 K. The initial guess for the temperature of the internal nodes is 301 K. Using the Jacobi method to iterate, complete the following sentences. a) The temperature of node (3,2) after the 2nd iteration is _____ K. b) The temperature of node (3,2) after the 3rd iteration is _____ K.
The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. If the tank wall has a thickness of 50 mm for cylindrical and hemispherical shells, The bolts were installed as 40 bolts/meter. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m. What is the maximum pressure that tank can contain.
Need asap A round brass rod 30 mm in diameter and 200 mm long is subjected to a compressive force of 100 kN. If μ = 0.33 and E = 105 GPa. Determine the change in diameter. In mm. Thanks
The A-36 steel pipe is subjected to the axial loading of 60 kN. Determine the change in volume of the material after the load is applied.
The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and 2014-T6 aluminum alloy respectively. When the temperature is at 65° F, ACE is in the horizontal position. Figure 1.5 in. -0.25 in. C 3 in. 1 of 1 اساساسا Part A Determine the vertical displacement of the pointer at E when the temperature rises to 160 ° F. (Figure 1) Express your answer with the appropriate units. SE = Value Submit Request Answer Provide Feedback Units ?
I Review Part A The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T = 15°C. (Figure 1) If the two 304-stainless-steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the temperature at which the average normal stress in either the magnesium or the steel first becomes 15.0 MPa Express your answer to three significant figures and include the appropriate units. HA T2 = Value Units Figure 100 mm 150 mm

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS