70002 R.Unknown G 800 Variable The arms of the Wheatstone bridge shown opposite are 700 ohm and 80 ohm respectively. An unknown resistor, believed to have a resistance of approximately 800 ohm, is to be measured. When the Variable resistor is set to 95 ohm the Wheat stone bridge is balanced. Calculate the value of the unknown resistor.

70002 R.Unknown G 800 Variable The arms of the Wheatstone bridge shown opposite are 700 ohm and 80 ohm respectively. An unknown resistor, believed to have a resistance of approximately 800 ohm, is to be measured. When the Variable resistor is set to 95 ohm the Wheat stone bridge is balanced. Calculate the value of the unknown resistor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The figure is shown a circuit consisting of a resistor Rị in series with two resistors R2 and R3 in parallel. The circuit is connected across a constant 100 V supply. When switch S is open, the ammeter A, reads 8 amperes. When switch S is closed A1 reads 10 amperes and A2 reads 4 A. determine (a) ohms of resistors R1, R2 and R3. (b) Voltage across R,& R2 when S is open. (c) Voltage across R1 & R2 when S is closed. R1 {A1 -v A2 S1 100V R2 R3
What is the greatest voltage that can be applied across a -W, 2.7-MQ resistor without causing it to overheat?
Q1b Determine Ia, Ib and Ic using elimination technique for the circuit in Figure Q1(b).
According to measured values given in following table, caculate the value of resistivity for each wire. Wire No R,(2) 4 (mm) L, (mm) Lwire (mm) rwire (mm) 1 935 1000 – 935 1000 0.25 2 485 1000 – 485 1000 0.175 3 795 1000 – 795 1000 0.35 4 794 1000 – 794 1000 0.35 664 1000 -664 1000 0.25 886 1000 – 886 1000 0.5
Determine the voltage across resistor R2. (assume Zener voltage is 3 volts)
If PMMC meter have internal resistance of 1002 and full-scale range of 1mA. Assume we wish to increase the meter range to 2A. the value of shunt resistor will be: OR_sh=0.00500 OR_sh= 0.00010 OR_sh=0.11111 0
Q6
We want to make a resistivity measurement. How should we connect the probes of the multimeter? Drag the connector images to the correct locations and "Not Connected" images to the rest. SLIDE SWITCH: LEFT- OFF MIDDLE- DC VVOLTS DC mA NUMERICAL VALUE OF VOLTS OR MA OR OHMS DISPLAYED HERE 0.00 OHMS FIGHT - AC VOLTS AC mA OFFOO AC DC-n DM 8010 MOVE ROTARY SWITCH TO THIS AREA TO READ OHMS (SELECT RANGE) 1000 200 20 MOVE ROTARY SWITCH TO THIS AREA TO READ VOLTS (SELECT RANGE) 20 200 2K 20K. 200 200K 2M 20M MOVE ROTARY SWITCH TO THIS AREA TO READ mA (SELECT RANGE) *20u 200u 200m 20m 10A mA COM PROBES Windows'u Etkinleştir Windows'u etkinleştirmek için Ayarlar'a gidin NOT CONNECTED
Determine the voltage across R1 in the figure below, if the source is 10 volts, the Zener is 6.8 volts, R1= 1k ohms and R2= 20k ohms.
R1 is connected in series with R2 and R3. R2 and R3 are in parallel. what is the value of current flowing thru R2 if the voltage supplied is 10 volts and if the resistors are all identical with value of 10 ohms A. 0.67A B. 0.33A C. 1.5A D. 1A
Determine the voltage across resistor 1, VR1 with E=8V, R1=657 ohms and R2=162 ohms.
Please answer the "required" portion. Show full solutions with brief explanation. Required: - total resistance in the picture - type of circuit (either parallel-series or series-parallel) between terminals - AC - BC