7.5 mm 300 mm 200 mm 15 mm

Q: Horizontal plates are connected to the bar AB whose length varies linearly from zero to HA, as…

A:

Q: 2 m hollow cast iron pole has an outside diameter of 250 mm and a thickness of 10 mm. The pole is…

A: Given Data P=15 kN D=250 mm t=10 mm

Q: A detailed view is shown for the connection Bin the concrete trough. The tension in cable B is 450…

A:

Q: The rectangular reinforced concrete column is reinforced with 6- 20 mm steel bars as shown. If b =…

A: Given Data B=250 mm D=400 mm d=20 mm(steel bar) P=400 kN

Q: The rectangular bar is connected to the support bracket with a 12-mm-diameter pin. The bar width is…

A:

Q: The C83400-red-brass 2014-T6-aluminum rod BC are joined at the collar B and fixed connected at their…

A:

Q: The internal drag truss for the wing of a light airplane is subjected to the forces shown. Determine…

A:

Q: A stainless steel tube with an outside diameter of 50 mm and a wall thickness of 5 mm is used as a…

A:

Q: The rigid block has a weight of 400 kN and is to be supported by posts A and B, which are made of…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is o₂ = 810 psi,…

A: FBD

Q: Provide final answer and equations used.

A:

Q: Q6/ If the allowable bearing stress for the material under the supports at A and Bis alle = 2MPA,…

A: It is mentioned that the reactions at the supports are only in vertical direction. The equivalent…

Q: The assembly is used to support the distributed load of w=500 lb/ft. determine effort normal in bar…

A: Given Force = 500 lb/ft Bar diameter = 0.4 in Bolt diameter = 0.3 in To find Normal stress in bar…

Q: A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determine…

A: Given data, Di = 100 mm. Tensile load = P = 400 KN = 400000 N. Stress= σ = 120 MN/ m2 = 120 N/mm2…

Q: Determine the stress in member CE assuming that the area in steel is 24 mm^2 p= 5 kN 3m 2m 2m 2m

A:

Q: The rectangular bar is connected to the support bracket with a 10-mm-diameter pin. The bar width is…

A:

Q: The concrete post is reinforced using six steel reiforcing rods, each having a diameter of 20 mm.…

A: Given data: Diameter of each rod = d = 20 mm Applied axial load = P = 900 kN Modulus of elasticity…

Q: The cylindrical steel column has an outer diameter of 90 mm and inner diameter of 80 mm. T column is…

A:

Q: A hollow steel tube with an inside diameter of 100mm must carry a tensile load of 400 kN. Determine…

A: We have to determine hollow steel diameter

Q: hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determine…

A: Given, the tensile load, P=400kN=400000N Stress, σ=120MPa Area, A=14πD2-14π1002=14πD2-10000

Q: A column of intermediate length buckles when the compressive stress is 40 ksi. If the slenderness…

A: Given data: The compressive strength of the column, σcr = 40 ksi. The slenderness ratio of the…

Q: circular tube AB is fixed at one end andfree at the other end. The tube is subjected to axialforce…

A:

Q: A 5 m long tension member (E=70GPA) has a cross sectional dimensions of 25mm x 50mm. if an axial…

A: Given data:

Q: The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When…

A:

Q: The horizontal bar shown is pinned at O and is supported with a helical spring at L1 from O. L1=2m,…

A:

Q: The 7/8-in.-diameter pins at A and C that support the structure are in single shear. Find the…

A:

Q: If the allowable bearing stress for the material under the supports at A and B is O₂ = 840 psi,…

A: Answer: Pmax = 11600 lb

Q: Q3/ Ir the allowable bearing stress for the material under the supports at A and B is opallow 2MPA ,…

A:

Q: The rigid bar of negligible weight is supported as shown. The middle helical spring is made of 22 mm…

A:

Q: If the gap between C and the rigid wall at D is initially 0.08 mm, determine the support reactions…

A: Given data: Deformation, δ=0.08 mm The value of, P=500 kN Young modulus, E=200 GPa. Calculate the…

Q: - The bell-crank mechanism is in equilibrium for an applied load of F₁ 15 kN applied at A. Assume a…

A: A bell crank is a tool that allows changing the working angle of a suspension component or linkage.…

Q: The bar is connected to the support using a pin having a diameter of d =lin. If the allowable…

A:

Q: If the yield strength for the bar is Gyield = 220 MPa, determine the maximum axial force P that can…

A:

Q: The composite bar is firmly attached to unyielding supports. Compute the stress in each material…

A: Given P = 320 kN = 320 X 103 N To find Stress of each materials

Q: The rectangular bar is connected to the support bracket with a 14-mm-diameter pin. The bar width is…

A:

Q: Determine the maximum axial force P that can be applied to the bar. The bar is made from steel and…

A: At the failure of the fillet To find out the concentration factor, K rh=0.251.25=0.2…

Q: The circular column is subjected to a compressive force of 5kN if the stress in the column is…

A:

Q: F E 2 m A B 2 m 1 m 1m

A:

Q: The bar has a diameter of 60 mm. If it is subjected to the force components as shown in the figure,…

A: Given data  d=60mm

Q: For the below assembly, if the gap between C and the rigid wall at D is initially 0.1 mm, determine…

A:

Q: If the allowable bearing stress for the material under the supports at A and Bis op = 820 psi,…

A:

Q: Problem The truss is made from three pin-connected members. Determine the maximum average normal…

A:

Q: The assembly is used to support a 10 kN point load at the tip as shown. The steel rod has a diameter…

A: Given: The load, F = 10 kN The diameter of steel rod, D = 12 mm The diameter of steel pin, d = 8 mm…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.