7.3-13 A shear wall in a reinforced concrete build- ing is subjected to a vertical uniform load of inten- sity q and a horizontal force H, as shown in the first part of the figure. (The force H represents the effects of wind and earthquake loads.) As a consequence of these loads, the stresses at point A on the surface of the wall have the values shown in the second part of the figure (compressive stress equal to 8 MPa and shear stress equal to 3 MPa). (a) Determine the principal stresses and show them on a sketch of a properly oriented element. (b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element. |8 MPa H з МРа A PROBLEM 7.3-13

7.3-13 A shear wall in a reinforced concrete build- ing is subjected to a vertical uniform load of inten- sity q and a horizontal force H, as shown in the first part of the figure. (The force H represents the effects of wind and earthquake loads.) As a consequence of these loads, the stresses at point A on the surface of the wall have the values shown in the second part of the figure (compressive stress equal to 8 MPa and shear stress equal to 3 MPa). (a) Determine the principal stresses and show them on a sketch of a properly oriented element. (b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element. |8 MPa H з МРа A PROBLEM 7.3-13

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve the following problems The composite bar in the figure is made of two segments AB and BC, having a diameter of 12 mm and 8 mm respectively. The you modulus of elasticity EAB = 90 GPa and EBC= 80GPa Critically evaluate the deformation of the bar shown under the given loads. the missing force F1 325KN. F=40KN F= kN A 4m 4.2m
The articular Cartilage is subjected to plane stress with normal stresses ox , o, and shear stress Txy, as shown in the figure. At a counterclockwise angle e = 30° from the x-axis, the normal stress is 3 MPa tension, and at an angle e = 50°, it is 2 MPa compression. Find the principals stresses. Ty 0, =10 MPa
A thick-walled cylinder with closed ends has internal and external radii 100 mm and 180 mm respectively, is subject to internal and external pressures of 148 MPa and 58 MPa respectively. Apply Lame's equations to find the following: Radial and hoop stresses at radii 120 mm, 140 mm and 160 mm respectively. (a) (b) Axial stress of the cylinder.
2.2-4 A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN, as shown in the figure. The cable has an effective modulus of elastic- ity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, what is the factor of safety with respect to failure of the cable? ▬▬
3 Solve it, and draw a free body diagram.
Solve the following problems The composite bar in the figure is made of two segments AB and BC, having a diameter of 12 mm and 8 mm respectively. The you modulus of elasticity EAB = 90 GPa and EBC= 80GPA Critically evaluate the deformation of the bar shown under the given loads. the missing force F1 55KN. F=40KN kN 4m 4.2m
The flat bar shown in the figure is subjected to tensile forces P = 3000 lb. The bar has thickness t = 0.25 in. a) If the designer wants to make a stepped bar with shoulder fillets as shown in the figure, determine R the maximum stresses for fillet radii R = 0.25 in. P and R = 0.5 in. if the bar widths are b = 4.0 in. and c = 2.5 in. b) Comment on the relation between the stress and the fillet radius each time it is increased. c) What is the factor of safety for each fillet radius if the part is made of cast iron Sut = 30 ksi? Solution: 3.0 2.8 D/d = 2 1.15 D. 2.6 1.5 2.4 2.2 - 1.05 O nom %3D %3D td к, 2.0 3.0 1.8 E 1.6 E 1.01 1.4 E 1.2 1.0 0.05 0.10 0.15 0.20 0.25 0.30 r/d
For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm2 and Young’s modulus E = 200 GPa. Let P = 95.8 kN. Determine: a) Strain energy for truss AC. Enter your answer in J to 2 decimal places. b) Strain energy for truss AB. Enter your answer in J to 2 decimal places. c) Strain energy for truss BC. Enter your answer in J to 2 decimal places. d) Strain energy for truss BD. Enter your answer in J to 2 decimal places. e) Strain energy for truss DC. Enter your answer in J to 2 decimal places. f) Strain energy for truss DF. Enter your answer in J to 2 decimal places. g) Strain energy for truss FC. Enter your answer in J to 2 decimal places. h) Strain energy for truss CE. Enter your answer in J to 2 decimal places. i) The displacement at point A. Enter your answer in mm to 2 decimal places.
Solve the following problems The composite bar in the figure is made of two segments AB and BC, having a diameter of 12 mm and 8 mm respectively. The you modulus of elasticity EAB = 90 GPa and EBC= 80GPA Critically evaluate the deformation of the bar shown under the given loads. the missing force F1 624KN. F=40KN kN B 4m 4.2m
None
PROBLEM 2. The carrier system in the figure consists of the AB rigid beam and two aluminum bars and a steel bar connected to it. After the assembly is created at 20 °C without causing any prestresses, calculate the stresses on the bars if the temperature is increased to 80 C. Steel A-36 A =160 mm? 3,5m 10 kN/m 3 m 3m 2 m 2014-T6 Aluminum A =200 mm E A,