7. An overhead 3- phase transmission line delivers 5000 KW at 22 kV at 0.8 p.f. lagging. The resistance and reactance of each conductor are 4 and 6 respectively. Determine i) sending end voltage ii) percentage regulation and iii) transmission efficiency.

Q: What are the steps for plotting points on microstation uisng offset, station, side and elevation?

A: We need to tell about steps for plotting points on microstation uisng offset, station, side and…

Q: A luminaire installed no less than 7.5 feet above the floor in a patient care area does not have to…

A: Given statement:  A luminaire installed no less than 7.5 feet above the floor in a patient care area…

Q: hat is the approximate voltage amplitude and frequency of the waveform below?

A: Disclaimer: "Since you have asked multiple questions, we will solve the first question for you. If…

Q: 2.) A corridor is 8 ft by 60 ft with a 10 ft ceiling. You want to determine the average illuminance…

A: Given, Length of the corridor, L=8 ft Width of the corridor, W=60 ft Height of the corridor,h=10 ft

Q: what is vehicle servicing

A: A motor vehicle service or tune-up is a series of maintenance procedures carried out at a set time…

Q: -6) Solid grounding is used for voltages

A: Solid is used for the voltages below:

Q: 0.048L 0.2728 0.32 0.08503 9A 4.7 2.80A Radio 20. 4.20V(* Battery Wind Solar Panel Repeator…

A: A thevenins equivalent circuit is used for solving complicated circuits, by converting the voltage…

Q: IS it a requirement to have a light ixture outside the garage door for a vehicle? O No Yes For two…

A:

Q: ladder diagram for three circuits, circuit A is one lampholder and one duplex receptacle controlled…

A: According to the question, we need to design a ladder diagram for three circuits, circuit A is one…

Q: 7- What is the uses of circuit breaker?

A: Step-1-> A circuit breaker is an electrical safety device designed to protect an electrical…

Q: A 636 kcmil 26/2 ACSR conductor has a GMR of _____ inch at 60 Hz. (Round-off answer in 3 decimal…

A: The GMR or Geometric Mean Radius of a conductor is an important parameter used in calculating its…

Q: Parallel conductors must be installed in sizes no smaller than A. 1/0. B. 2/0. C. 750 kcmil. D. 4/0.

A: Given To determine minimum size of conductors  that must be used in parallel conductors

Q: Vdc0 U=12 V Circuit #1 Ried LED www Ried_series Vdc0 U= 12 V Current in LED (A) Circuit 0.03 #₂ 0.02…

A: Given Data:An LED illumination circuit with,Supply voltage Set-current of the diodes V-I…

Q: Using group revamping all lamps are usually replaced when they have reached what percentage of rated…

A: It is asked to tell the percentage of rated life expectancy at which lamps are replaced using group…

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.