a. Explain autotransformer starting method and wye-delta starting method of 3-Dinduction motor with necessary circuit diagram.7b. Discuss built-in undervoltage and overload protection of 3-O induction motorwith neat sketch.c. A 3-0, 6-pole, 460V, 60HZ induction motor rated at 15hp is running at1185rpm. The equivalent circuit has the following parameters (in ohms/phase):R¡=0.22, R2=0.252, X1=1.2 N, X=1.29 N, Rc=317 2, Xm=42 2i)Sketch the per phase equivalent circuit of the induction motor (with respect tostator)ii)Calculate slip and rotor frequencyiii) Stator current and total stator copper loss.

Note: We are authorized to answer one question at a time since you have not mentioned which question…

Answered: 7 a. Explain autotransformer starting…

7 a. Explain autotransformer starting method and wye-delta starting method of 3-D induction motor with necessary circuit diagram. b. Discuss built-in

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Fill in the blank: 1- Lap winding is suitable for ----- current, voltage d.c. generators. 2-A 220 V shunt motor develops a torque of 54 N-m at armature current of 10 A. The torque produced when the armature current is 20 A, is N-m. 3- The d.c. series motor should never be switched on at no-load because 4- The equation relating the generated e.m.f., E, terminal voltage, armature current and armature resistance for a d.c. motor is E = ‒‒‒‒‒‒‒‒‒‒‒ 5- A transformer having 1000 primary turns is connected to a 250 V a.c. supply. For a secondary voltage of 400 V, the number of secondary turns should be turns. 6- The equivalent resistance of the primary of a transformer having N2/N1 = 5 and R1 = 0.1 ohm when referred to secondary becomes ohm. 7- The maximum efficiency of a 100 kVA transformer having iron loss of 900 W and F.L. cu loss of 1600 W occurs at - kVA. ‒‒‒‒‒‒ ‒‒‒‒‒‒‒ 8- If Cu loss of a transformer at 7/8 full load is 4900 W, then its full-load Cu loss would be watt.
What do you mean by 'static', 'alternating’, and 'rotating' magnetic field? Explain the significances of the rotating magnetic field in rotary machines. What are the purposes of using starter in a three-phase induction motor? With neat diagrams, explain the operation of a Wye-Delta starter for a three phase induction motor.
d) A 2-pole induction motor is fed with a 230 V, 50 Hz supply and is running at no load. i. Calculate its angular speed in rpm. ii. Explain how can we slow down the speed of the motor above, at no load? iii. Explain what will happen to the speed of the motor if we slowly add amechanical load to the motor.
Q3. (a) For a three-phase squirrel-cage induction motor (SCIM), explain: (i) Why is the motor efficiency relatively low at light and heavy loads? (ii) Under what condition that the motor has the maximum efficiency?
Q2. A 230 V single-phase induction motor, 50 Hz, has the following winding impedances (at rest): Zm=28 <70° Q. Za=42 <45°Q A) Calculate the input current at start-up. B) Obtain the amount of capacitor in series with the auxiliary winding for which the torque Maximum startup. Then compare the input current, auxiliary winding current and torque all at start-up in two modes with and without starter capacitor.
A 4-pole ,400 V, 50 Hz wound-rotor induction motor has the following circuit model parameters: R = 0.3 2, R2 = 0.25 2, X X2' 0.6 2, Xo 35 2 and rotational loss of 1500 W ( Ro is negligible). When the motor running at 1425 rpm, %3D %3D %3D %3D calculate a) the motor efficiency and, b) the maximum gross power when exciting circuit is omitted.
Question A 3-phase, 415 V, 4-pole, 50 Hz induction motor draws 5 times the rated current at rated voltage at starting. It is required to bring down the starting current from the supply to 2 times of the rated current using a 3-phase autotransformer. If the magnetizing impedance of the induction motor and no-load current of the autotransformer is neglected, then the transformation ratio of the autotransformer is given by
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 4 ALoad torque=Tload= 7 Nm
4. A shunt generator has a full load current of 196 A at 220 V. The stray losses are 900W and the shunt field coil resistance is 75N. If it has a full load efficiency of 90%, find the armature resistance.
A 500 V DC shunt motor takes 4 A at no-load. The shunt field winding resistance and the armature winding resistance are 250 and 0.2 respectively. Find the efficiency when the motor draws a current of 10 A at full load.