Q2 A DC shunt motor is connected to a 220 V supply. Figurel below shows the time/current characteristics with a resistance starter. If armature resistance is 0.120, a) What is the maximum current that is flowing in the armature at the instant of starting? b) What is the minimum current in the armature? c) How many sections does this starter resistance have? Show your work. d) Calculate the required starter resistance required to limit the current to the maximum value.

Q2 A DC shunt motor is connected to a 220 V supply. Figurel below shows the time/current characteristics with a resistance starter. If armature resistance is 0.120, a) What is the maximum current that is flowing in the armature at the instant of starting? b) What is the minimum current in the armature? c) How many sections does this starter resistance have? Show your work. d) Calculate the required starter resistance required to limit the current to the maximum value.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

"A 50 hp, 220 V shunt motor operating at 1200 rpm draws a line current of 94 A when operating at rated conditions. A 1.8 ohm resistor inserted in series with the armature causes the speed to drop to 840 rpm. The respective field circuit resistance and armature circuit resistance are 55 ohm and 0.2 ohm. What will be the new armature current(in Amp)?"
The armature circuit of a free excited direct current motor with a nominal voltage of 600 V is fed from an adjusted direct voltage source. The excitation circuit is also powered from a regulated voltage source. It is used in an application that requires motor speed adjustment. The speed of the motor at the nominal armature voltage was measured as 1600 rpm. All losses of the motor and voltage source and the effect of armature reaction are neglected. It is accepted that the engine is not saturated.Answer the questions below.a) Draw the armature and excitation circuit of the motor and write the formulas for the equivalent circuit.b) If the load moment of the motor at the nominal armature voltage is 420 Nm, then calculate the armature current and the input power of the motor.c) If the armature voltage of the motor is kept constant at 600 V and the excitation current is decreased until the speed reaches 4000 rpm, then calculate the shaft moment. Show this working area on the M = f (W) axis.
A four-pole DC shunt motor, 220 V, the number of conductors in the armature 1000, the typical winding coil, the motor draws 52 A, the magnetic flux per pole 0.02 Wb, the armature resistance 0.2 02, and shunt resistance 110 Q. Calculate motor speed.
A shunt-wound DC motor with the field coils and rotor connected in parallel (Figure 1) operates from a 130 V DC power line. The resistance of the field windings, R. is 208 n. The resistance of the rotor, R,, is 4.90 1. When the motor is running, the rotor develops an emf E. The motor draws a current of 4.46 A from the line. Friction losses amount to 45.0 W Part C Compute the emf E. • View Available Hint(s) Tematates Symbols undo redo Tese keyboard shortcuts Help V Submit Part D Compute the rate of development of thermal energy in the field windings. Express your answer in watts. > View Available Hint(s) Templates Symbols undo redo Teset keyboard shortcuts Help Pan,windings = Figure W K 1 of 1 Submit Part E Compute the rate Pin.rotor of development of thermal energy in the rotor. R ER, Express your answer in watts. > View Available Hint(s) Templates Symbols undo redo teset keyboard shortcuts help Pinrotor=
A 12 pole DC shunt generator has an armature resistance of 0.02 2 The armature is lap wound with 620 conductors, when driven at 750 RPM the machine produces a total armature current of 500 A at a terminal voltage of 100 V. Calculate the total useful flux. If the armature winding is reconnected as wave calculate the terminal voltage.
DC Motor Speed Regulation A shunt DC motor Armature resistance is 1 ohm and field coil resistance is 100 ohms. Back emf constant is 9 volts for 100 RPM. The DC supply Voltage is 100 V and it is running with a speed 1000 RPM. What is DC supply current?
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 3 ALoad torque=Tload= 8 Nma) 143 rpmb) 734 rpmc) 1361 rpm d) 77 rpm e) 1333 rpm
Q3-A)- A 220 V d.c. Shunt motor has a shunt field resistance of 11002 and an armature resistance of 0.2. For a given load, motor runs 600 r.p.m drawing a current of 52A from the supply. If a resistance of 11002 is added in series with the field winding. Find the new armature current and the speed. Assume load torque constant and magnetization curve to be linear } B)- What are the factors that affect the speed of d.c. Motor
A full load current of 50 A is generated by a 250 V d.c. shunt motor with a 0.5 ohm armature resistance. When a 1 ohm resistance is connected in series with the armature, what is the ratio of stalling torque to full load torque?
10. What is a potent PRACTICAL APPLICATIONS 1. You are an electrician on the job. It is decided that the speed of a large DC motor is to be reduced by connecting a resistor in series with its armature. The DC voltage applied to the motor is 250 V, and the motor has a full-load armature current of 50 Your job is to reduce the armature current to 40 A at full load by connecting the resistor in series with the armature. What value of resistance should be used, and what is the power rating of the resistor? 2. You are working on an electronic circuit. The circuit current is 5 mA. A resistor is marked with the following bands: brown, black, red, gold. A voltmeter measures voltage drop of 6.5 V across the resistor. Is this resistor within its tolerance rati 3. A homeowner uses a 100-watt incandescent lamp as a heater in an outside w pump house to protect the pump from freezing in cold weather. Unfortunately however, the lamp can burn out and leave the pump unprotected. You have b asked to…
determine "A" through "G" for the DC motor on worksheet 5 when it is running at capacity and its specification are as follows rated input 125volt 16 amp armature resist. 0.3 ohms shunt field resist 50 ohm series field resist. .6 ohm rheostat resist. 12.5 ohm . power consumed by armature resistance a- 54.68 W b- 312.5 W c- 1632.83 W d- 2000 W
A DC series motor having a resistance of 0.4 ꭥ and runs at 2000 rpm when connected to 250 V supply and drawing a current of 20 A. (i) What resistance must be added in order to limit the speed to 4000 rpm when armature current is 5A? Assume flux varies linearly. (ii) What resistance must be added to limit the speed to 1000 rpm when armature current is 30 A? Assume that the flux at 30 A is 20% more than that at 20A. (iii) At what speed the motor will run if it is connected directly to 250 V supply when the load is such that the current drawn is 30 A?