(7) A universal joint shown has a pin whose Sy = 485N/mm2 & d = 15mm. Its pin-bush has a length a = 62mm. The shaft turns 400rpm. (a) What is the torque that maybe transmitted for shear with a factor of safety = 5; (b) In order not to have excessive wear on the pin, the average bearing pressure should not exceed 20x103 kPa, compute the transmitted torque. (c) What is the transmitted power in both cases?

Q: The 2.0-in-diameter solid steel shaft shown is simply supported at the ends. Two pulleys are keyed…

A:

Q: Q/ Figure below shows the load components acting on a helical gear mounted on a simply supported…

A: Given data Diameter of the shaft =20 mm Ry1+Ry2=2KN2×127+68.42=Ry2×177Ry2=322.42177=1.8215…

Q: The rotating shaft in the given figure is machined from AISI 1020 CD steel. It is subjected to a…

A:

Q: 4) Compute the fatigue life of a rotating hub and shaft assembly, if at a critical point in the…

A: Step 1: Step 2: Step 3: Step 4:Step 5:Step 6:Step 7:

Q: Required information The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft…

A:

Q: yield strength of oy 750 MPa. Determine the design factor of safety using Tresca and von Mises…

A: DefinitionTersca Theory:A ductile material fails or yields when its maximum shear stress equals or…

Q: Figure 1 is a schematic drawing of a countershaft that supports two V-belt pulleys. For each pulley,…

A: Given data, For pulley A Tension in tight side, T1 = 103 N Tension in loose side, T2 = 0.15T1…

Q: The figure shows a shaft mounted in bearings at A and D and having pulleys at B and C. The forces…

A: Given:- Shaft is made up of AISI 1035 CD steel Speed of shaft = 1000 rpm  To Find:-  Minimum…

Q: Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia =…

A: Write the given data with suitable variables: P=426 lbdmin=0.1959 in

Q: Determine the endurance limit for this material as well as the value after correction for surface…

A: Given Data: AISI 1020 CD steelF=8 kNσe=235 MPa   To Find: The endurance limit after correction.

Q: The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and…

A: To findDetermine the minimum fatigue factor of safety based on achieving infinite life. If infinite…

Q: A solid 4340 HR Steel tie rod of length Lrod = 850 mm is employed to compress a 6061-T6 aluminum…

A: 4340 HR steel rod.Diameter of the rod, drod= 22.5 mmLength of the rod, Lrod= 850 mm6061-T6…

Q: naft has a diameter of 41mm. The PCD of the coupling bolts is 63mm. amter is 3mm, and the yield…

A: Given data-T=354Nm  D=41mmPCD=63mm

Q: 42, The static deflection at the center of the steel shaft in Fig. 3-53 is equal to 0.35 mm. Find…

A: Given: The static deflection of shaft, x= 0.36 mm

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.