7-70. The assembly consists of three disks A, B, and Cthat are used to support the load of 140 kN. Determine thesmallest diameter di of the top disk, the diameter dy withinthe support space, and the diameter dy of the hole in thebottom disk. The allowable bearing stress for the materialis (a.)ler - 350 MPa and allowable shear stress isTlon - 125 MPa.140 kNd.20 mm10 mm

Assume bearing failure for disk B,σballow=PA=Pπ4d12σballow=4Pπd12d1=4×140×1000π×350d1=22.57 mm…

Answered: 7-70. The assembly consists of three…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 510-kg engine is suspended from the jib crane at the position shown. (Figure 1) Figure 2m 2 m 2 m 430 D a 0.4 m 150 mm T 150 mm 20 mm- A 20 mm + T 300 mm 20 mm Section a-a 1 of 1 Part A Determine the normal stress at point A on the cross section of the boom at section a - a. Express your answer using three significant figures and include the appropriate units A= -3.327 Submit Previous Answers Request Answer Part B HÅ ^ * Incorrect; Try Again; 5 attempts remaining TA = Submit Determine the shear stress at point A. Express your answer to three significant figures and include the appropriate units. D Provide Feedback MPa μA Value Request Answer ? Units BE ?
4 ft B -3 ft- D 3 ft C If the load P causes wire BD to stretch by 0.03 inches, determine the stress in wire BD. The wire is made of A36 steel.
The joint is subjected to the axial member force of 6 kips. Determine the average normal stress acting on sections AB and BC. Assume the member is smooth and is 1.5 in thick. . Tip: You can determine the forces by making a FBD in a concurrent point. 1.5 in B 20⁰ 4.5 in. 6 kip 50⁰
The bars of the truss each have a cross-sectional area of 1.25 in2. Determine the average normal stress in members AB, BD, and CE due to the loading P = 6 kip. State whether the stress is tensile or compressive.
Calculate the stress perpendicular to the inclined plane AB. Report your answer as a positive number.Answer: σn= Enter your answer in accordance to the question statement ksi.
Similar problem already solved on bartleby. Take reference from there.
The assembly consists of three disks A, B, and C that are used to support the load of 140 kN. Determine the smallest diameter d₁ of the top disk, and the largest diameter d₂ of the opening, and the largest diameter d3 of the hole in the bottom disk. The allowable bearing stress for the material is (b) allow = 350 MPa and the allowable shear stress is Tallow=125 MPa. C B d₁ -| A 140 kN 20 mm 10 mm d3 d2
As shown in the picture below, the sloping direction of the member is subjected to a compression of 3,000 N. contact surfaceDetermine the compression stress generated by AB and BC and the shear stress acting on the horizontal plane DB.
Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 40 kN if it developed a stress of 35 MPa. Take note that the inner diameter is 3/6 of the outer diameter.
The pin support A and roller support B of the bridge truss are supported on concrete abutments. If the allowable bearing stress of the concrete is oallow = 2 ksi, determine the required minimum dimension of the square bearing plates at C and D to the nearest 1/16 in. 150 kip 100 kip B 200 kip 300 kip 300 kip 300 kip 300 kip -6 ft --6 ft--6 ft--6 ft--6 ft--6 ft-
The beveled gear is subjected to the loads shown.Determine the stress components acting on the shaftat point B, and draw the results on a stress elementat this point. The shaft has a diameter of 1 in. and isfixed to the wall at C. A = 0.7854 in2 J = 0.098175 in4 I = 0.049087 in4 (QB)z = 0 (QB)x = 0.0833 in3
The d - 15-mm-diameter solid rod passes through a D=20-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b- 13 mm. The rod head has a diameter of a = 30 mm, and the head has a thickness of t= 10 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 90 MPa, and the bearing stress between the rod head and the support plate cannot exceed 140 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate Rod Answer: Pmax i -Hole diameter D Head kN ام

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS