7-69. The two aluminum rods AB and AC have diametersof 10 mm and 8 mm, respectively. Determine the largestvertical force P that can be supported. The allowable tensilestress for the aluminum is olow - 150 MPa.

Answered: 7-69. The two aluminum rods AB and AC…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

13-50. The C-frame is used in a riveting machine. If the force at the ram on the clamp at Dis P -8 kN, sketch the stress distribution acting over the section a-a. -200 mm- 10 mm 60 mm -10 mm
*9-56. The CX3400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T; = 10"C, determine the average normal stress in cach member when 7; = 45 "C. Alsa, how far will the collar be displaced? The cross-sectional area af each member is 1130 mm. -மீ
4 ft B -3 ft- D 3 ft C If the load P causes wire BD to stretch by 0.03 inches, determine the stress in wire BD. The wire is made of A36 steel.
The joint is subjected to the axial member force of 6 kips. Determine the average normal stress acting on sections AB and BC. Assume the member is smooth and is 1.5 in thick. . Tip: You can determine the forces by making a FBD in a concurrent point. 1.5 in B 20⁰ 4.5 in. 6 kip 50⁰
The bars of the truss each have a cross-sectional area of 1.25 in2. Determine the average normal stress in members AB, BD, and CE due to the loading P = 6 kip. State whether the stress is tensile or compressive.
The screw of the clamp exerts a compressive force of 500 lb on the woodblocks. Sketch the stress distribution along section a–a of the clamp. The cross section is rectangular, 0.75 in. by 0.50 in.
Determine the shortest distance d to the edge of the plate at which the force P can be applied so that it produces no compressive stresses in the plate at section a–a. The plate has a thickness of 10 mm and P acts along the centerline of this thickness.
7-63. The cotter is used to hold the two rods together. Determine the smallest thickness t of the cotter and the smallest diameter d of the rods. All parts are made of steel for which the failure normal stress is fail 500 MPa and the failure shear stress is fail 375 MPa. Use a factor of safety of (F.S.), = 2.50 in tension and (F.S.), = 1.75 in shear. -d- 30 kN 40 mm d - 30 kN t Prob. 7-63 10 mm =
4- If the normal stress in member AB is 6000 psi, what is the normal stress in member BC? Determine the axial deformation at C. E = 30000 kai 2 in 3 in Ө 24" Im 20"
The assembly consists of three disks A, B, and C that are used to support the load of 140 kN. Determine the smallest diameter d₁ of the top disk, and the largest diameter d₂ of the opening, and the largest diameter d3 of the hole in the bottom disk. The allowable bearing stress for the material is (b) allow = 350 MPa and the allowable shear stress is Tallow=125 MPa. C B d₁ -| A 140 kN 20 mm 10 mm d3 d2
Determine the maximum force P that can be exerted on each of the two pistons so that the circumferential stress in the cylinder does not exceed 3 MPa. Each piston has a radius of 45 mm and the cylinder has a wall thickness of 2 mm.
The d - 15-mm-diameter solid rod passes through a D=20-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b- 13 mm. The rod head has a diameter of a = 30 mm, and the head has a thickness of t= 10 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 90 MPa, and the bearing stress between the rod head and the support plate cannot exceed 140 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate Rod Answer: Pmax i -Hole diameter D Head kN ام

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

7-69. The two aluminum rods AB and AC have diameters of 10 mm and 8 mm, respectively. Determine the largest vertical force P that can be supported. The allowable tensile stress for the aluminum is olow - 150 MPa.