6Kip 6 Kips 15 kys 8-4 3ft 6ft 2ft 2F beam is supported by a Neglecting roller at A and by a pin at 8. the weight of the beam, delermine the ractions at A and B. (that : Daw fre-body diagram and use equilibrium eguelims).

Q: A piston-cylinder device contains 1.5 kg of steam at 300°C and 0.4 MPa. Steam is cooled at constant…

A: The initial conditions are: The specific volume of the steam can be determined from the steam table…

Q: D Question 2 Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your…

A: Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your paper and…

Q: What is the value of w and y? y W 6V2

A:

Q: A pneumatic system operating at 85 psi comprises a series of pneumatic actuators which consume 2.4…

A: Original CFM = 2.4 CFMOriginal pressure= 85 psiNew pressure= 120 psiAtmospheric pressure= 14.7 psi

Q: QUESTION I ) Sute True or False for the following statements: O The principal stresses represent the…

A: Disclaimer: Since you have asked multiple questions we will solve the first one for you. If you want…

Q: 11 .625 .125 SECTION A-A VIEW B-B .344 1.000 .313- 0.2407+.0013 -.0013 10 .125 8 B A Q 3.875 NO…

A: Given: Name these lines.

Q: A hydro-electric dam uses turbines to generate electricity as reservoir over the turbine blades. A…

A: (a) To fill: The blanks of the statement with appropriate choice. Explanation: Hydroelectric dam: A…

Q: Question attached

A: (a) Relative humidity is the ratio of the partial pressure of water vapour in the mixture to the…

Q: Round number to three significant figures. 1.548937 x 10^7

A: For scientific notations significant digits/figures are calculated only for the coefficient or…

Q: Can I get a more detailled explenation on how to get the numbers in the numetor in each fraction…

A:

Q: Which best represents the Slope-field and streamlines for dy = y? – 9 dt

A:

Q: 150 m 50 mm 85 mm Section X-X 20 kN

A:

Q: Which of the following statements below are incorrect? select all which apply.     A shear force…

A: It is needed to provide the wrong or incorrect statements.

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: a) Calculate the area of the plate. A= Number in?

A: Given:

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A:

Q: 50 mm 150 mm 50 mm 85 mm Section X-X 20 kN

A: Let us shift the load to section X-X. The moment M and force P will create the same effect.

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.