68. Water at a rate of 1 m'/s enters a small hydraulic turbine from the horizontal supply line, having a diameter of 50 cm. The pressure at the inlet (stage 1 in the figure) is 200 kPa. Pressure in the turbine discharge conduit (the draft tube) at location 2, which is 2 m below the turbine centerline, is measured as 55 kPa. Find the shaft head and the horsepower developed by this turbine. Use D2 = 65 cm.

68. Water at a rate of 1 m'/s enters a small hydraulic turbine from the horizontal supply line, having a diameter of 50 cm. The pressure at the inlet (stage 1 in the figure) is 200 kPa. Pressure in the turbine discharge conduit (the draft tube) at location 2, which is 2 m below the turbine centerline, is measured as 55 kPa. Find the shaft head and the horsepower developed by this turbine. Use D2 = 65 cm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

To insulate a device against a high external temperature, which of the following are practical routes: Select one or more: a. Lay down a dense tough polymer coating b. Plasma-deposit a dense, high strength ceramic coating c. Assemble a high-strength metal alloy shell on the outside of the device d. Create an outer layer with a solid shell filled with a porous material made out of a ceramic
Nylon 6,6 is a thermoplastic polymer with high mechanical strength, high resistance to chemical environments, and good stability under heat. Therefore, it is well suited to be used in 3D structural objects. A cylindrical nylon 6,6 pipe is made by injection molding. The pipe is 1 m long with an outer diameter of 8cm, and a thickness of 2mm. The crystallinity of the pipe is 25%. The density and associated percent crystallinity for two nylon 6,6 samples are measured as below: ρ(g/cm3) crystallinity (%) 1.190 67 1.155 44 If the degree of polymerization is 500, calculate the number of chains in the pipe. (Assume the chains are equal in length).
Compression molding is a manufacturing process in which the molding material is preheated then placed in an open mold cavity where the compressive action of the punch forces the polymer into the desired shape as shown in the figure below. Based on your understanding of the behavior of polymers, which of the statements below regarding compression molding of polymers are accurate? Punch Cavity C. -Upper mold half Charge 41 (1) -Lower mold half Knock-out pin V, F |x.F (2) and (3) Molded part a. Lower operating temperatures are more desirable as they reduce viscosity making it easier to fill the cavity b. This process can only be used for thermosets as they can thermally cure from monomer state This process can be used for both thermosets and thermoplastics as they can both be thermally shaped d. This process is suitable for rubber, PVC and polymethyl methacrylate
I1
Silica gels are a form of SiO2 characterized by: (This question has more than one correct answer) a. Crystalline lattice b. High internal surface area c. Presence of OH ions d. Can be used as a catalyst support
What factors influence the crystallinity ofpolymers? Explain the development androle of crystallinity in PET and nylon.
i need the answer quickly
Q5 (a) Figure 6 shows two types of polymeric products fabricated using different processing techniques. Suggest with justification for the type of processes used to produce the products: i. Product A ii. Product B A B Figure 6. Two types of polymeric products (a) plastic bottles and (b) plastic car boot tray (b) The molecular weight data of a Polymer X are given in Table 3. Once undergone a melting process, it achieves degree of polymerization, DP of 498 upon solidification. i. Calculate the number-average molecular weight (Mn) for the polymer. ii. Calculate the molecular weight for monomers of the Polymer X. iii. Prove that the Polymer X is a polytetrafluoroethylene (PTFE) with chemical formula of (C2F4)n- Given the atomic weights for carbon, C is 12.011 g/mol and fluorine, F is 18.998 g/mol.
1. Explain in 1-3 bullets how as a practicing engineer you determine the yield strength of a thermoplastic polymer from a tensile stress-strain curve. 2. Explain what is happening at the yield strength for a thermoplastic polymer from a physical standpoint in 1-3 bullets. (e.g. what are the atoms or polymer chains doing?)
Molecular weight data for some polymer are tabulated here. Compute (a) the number-average molecular weight, (b) the weight-average molecular weight. (c) If it is known that this material's degree of polymerization is 710, which one of the polymers listed in Table 14.3 is this polymer? Why? Molecular Weight Range g/mol 15,000-30,000 Xi Wi 0.04 0.01 30,000-45,000 0.07 0.04 45,000-60,000 0.16 0.11 60,000-75,000 0.26 0.24 75,000-90,000 0.24 0.27 90,000 105,000 0.12 0.16 105,000-120,000 0.08 0.12 120,000-135,000 0.03 0.05
I need the answer of this
Plz need explanation ?