Compression molding is a manufacturing process in which the molding material is preheated then placed in an open mold cavity where thecompressive action of the punch forces the polymer into the desired shape as shown in the figure below. Based on your understanding of thebehavior of polymers, which of the statements below regarding compression molding of polymers are accurate?PunchCavityC.-Upper mold halfCharge41(1)-Lower mold halfKnock-out pinV, F|x.F(2) and (3)Molded parta. Lower operating temperatures are more desirable as they reduce viscosity making it easier to fill the cavityb. This process can only be used for thermosets as they can thermally cure from monomer stateThis process can be used for both thermosets and thermoplastics as they can both be thermally shapedd. This process is suitable for rubber, PVC and polymethyl methacrylate

Compression molding process is used to give a desired shape to the plastic with the use of high…

Compression molding is a manufacturing process in which the molding material is preheated then placed in an open mold cavity where the compressive action of the punch forces the polymer into the desired shape as shown in the figure below. Based on your understanding of the behavior of polymers, which of the statements below regarding compression molding of polymers are accurate? Punch Cavity (1) Charge Upper mold half Lower mold half Knock-out pin (2) and (3) Molded part P ☐a. Lower operating temperatures are more desirable as they reduce viscosity making it easier to fill the cavity b. This process can only be used for thermosets as they can thermally cure from monomer state ☐ c. This process can be used for both thermosets and thermoplastics as they can both be thermally shaped Od. This process is suitable for rubber, PVC and polymethyl methacrylate

Compression molding is a manufacturing process in which the molding material is preheated then placed in an open mold cavity where the compressive action of the punch forces the polymer into the desired shape as shown in the figure below. Based on your understanding of the behavior of polymers, which of the statements below regarding compression molding of polymers are accurate? Punch Cavity (1) Charge Upper mold half Lower mold half Knock-out pin (2) and (3) Molded part P ☐a. Lower operating temperatures are more desirable as they reduce viscosity making it easier to fill the cavity b. This process can only be used for thermosets as they can thermally cure from monomer state ☐ c. This process can be used for both thermosets and thermoplastics as they can both be thermally shaped Od. This process is suitable for rubber, PVC and polymethyl methacrylate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Which of the following are incorrect regarding the crystallinity and mechanical behavior of polymers? a. As temperature is reduced, necking behavior of plastic tensile bars completely disappears b. Semi-crystalline polymers are heat treated to increase crystallinity and improve strength c. Heat treatment always results in enhanced polymer strength, modulus, and brittleness d. Strain softening happens in elastomers where the deformation gradually leads to a decrease in stiffness under constant strain rate e. Increasing the degree of crystallinity generally increases polymer strength, elastic modulus, and ductility in semi-crystalline polymers f. The stress-strain curve slope for totally elastic and brittle polymers is always positive
Which statements are correct regarding the mechanical properties of polymers? a. Drawing increases alignment and strength, and decreases ductility (% elongation) b. Annealing increases alignment, strength and elastic modulus c. Increasing temperature results in increased elastic modulus and strength, and decreased elongation d. Decreasing strain rate causes decreased strength and elastic modulus and increased elongation e. A higher degree of crosslinking generally results in decreased percent elongation at break, and increases strength
Which is correct for 8 and Which is correct in 9?
Which of the following are incorrect regarding the crystallinity and mechanical behavior of polymers? a. Strain softening happens in elastomers where the deformation gradually leads to a decrease in stiffness under constant strain rate b. As temperature is reduced, necking behavior of plastic tensile bars completely disappears C. The stress-strain curve slope for totally elastic and brittle polymers is always positive d. Heat treatment always results in enhanced polymer strength, modulus, and brittleness e. Semi-crystalline polymers are heat treated to increase crystallinity and improve strength f. Increasing the degree of crystallinity generally increases polymer strength, elastic modulus, and ductility in semi-crystalline polymers
(a) There are three main sub-groups of engineering polymers with distinct differences in their structures. Name these sub- groups; describe their structural differences and bonding mechanisms.
Explain how macroscopic plasticity occurs in polymers from the point of view of microscopic mechanisms (covered in the chapters indicated in the Callister book). (maximum of 3 lines, not counting the space for possible schematic figures).
At room temperature, most polymers have similar fracture toughness compared to metals. O True False
Hello Sir.Good Evening I have a question in my home work related materials polimer lesson. The following below is my question. Please advice, thank you so much. "Explain how the relationship between temperature and the tensile strength of polymers ?"
1 Which one below is true for thermoplastic polymers? * O They do not soften when heated and do not harden when cooled. O Most cross-linked polymers are thermoplastics. O None of them. O They are harder and stronger than thermosetting polymers.
State the critical difference in the processing behavior of thermoplastics vs. thermosets.
What is the tensile strength of a composite fibre when its diameter is 20 microns and its critical fibre length is 30 microns? The strength between the fibre and matrix is 150 MPa.
Answer whats in the image, please and thank you