660.60 in.1.60 in.0.40 in.-0.80 in.-→Shape of a slug for Problem 1-62.FIGURE P1-62 Figure P1-62 shows the shape of a slug to bepunched from a sheet of steel 0.194 in. thick.Compute the shear stress in the steel if a punchingforce of 45 000 lb is applied.1-62.

Given data as per question Thickness of sheet to be punched = 0.194 in. Punching force = 45000lb

Answered: 66 0.60 in. 1.60 in. 0.40 in. -0.80…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A sphere and cylinder shown in (Figure 1) are released from rest on the ramp at t = 0. Part A If each has a mass m and a radius r, determine their angular velocities at time t. Assume no slipping occurs. Express your answers separated by a comma in terms of some, all, or none of the variables m, r, t, 0, and the acceleration due to gravity g. = لا ولها Submit VAΣo vec Request Answer ?
Problem 1: Solve for the COG, Ix and Ix the composite figure. Ix for half circle: (- Ix for rectangle: bh%/2 2in そ 3in COG half circle; 4r Lin 2in 2in
Please answer it correctly and read carefully. SHOW SOLUTION STEP BY STEP PLEASE
5 The best size wire is fitted in a groove of a metric screw such that the wire touches the flanks of the thread on the pitch line as shown in the figure. The pitch (p) and included angle of the thread are 4 mm and 60°, respectively. The diameter of the best size wire is mm (round off to 2 decimal places). Pitch line Flank 60⁰ Wire 0.25p -0.5p-
Answer is 17.4N horizontally and 17.8N vertically.Please show steps in detail.
Solve it from 1 to 4 PLZ
(b) In Figure Q5, the 17 kg of circular disk is originally rotating with a clockwise angular velocity, o = 49 rad/s at the end of the link BC. Given the kinetic coefficient of friction, uk = 0.25 when the disk is then placed against the wall. (i) Draw the kinetic diagram of all forces exerted on the circular disk. (ii) Calculate the force of link BC. (iii) Calculate the angular acceleration of the circular disk. (iv) Calculate the time required to stop the motion of the circular disk,
Problems 5-111 through 5-116 Figures P5-111 through P5-116 show completed shearing force diagrams for beams. Develop the loading diagram and the bending moment diagram for each beam.
Please solve it correctly using the expression. I don't know why there is a factor 1488 in numerator.
Given Answer: (0.827 in, 1.37 in) complete all steps please
The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are rotated through 180°? Assume the radius of the bicycle wheel is 12.7 inches. The bicycle will travel approximately (Round to the nearest tenth.) in. C -1.95 in 4.21 in

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

66 0.60 in. 1.60 in. 0.40 in. -0.80 in.- → Shape of a slug for Problem 1-62. FIGURE P1-62 Figure P1-62 shows the shape of a slug to be punched from a sheet of steel 0.194 in. thick. Compute the shear stress in the steel if a punching force of 45 000 lb is applied. 1-62.