60 P1 D2 D1 The last 40 C until the water vapor pressure in the tube shown in Figure 0.75t/m d. Be that atmospheric pressure in the high current 68 cm-Hg-column, one section of dianeter D-60 em the second section of diameterD, = 14 cm. the first pressure value in the section P-0.35 kg / cm by that the cavitation neglecting the energy losses Determine the flow rate to start. Note: Use a period (.) as a decimal separator in your answers. Otherwise, even if your result is correct, it will be considered incorreet by the system. 3. Q m'/sec

60 P1 D2 D1 The last 40 C until the water vapor pressure in the tube shown in Figure 0.75t/m d. Be that atmospheric pressure in the high current 68 cm-Hg-column, one section of dianeter D-60 em the second section of diameterD, = 14 cm. the first pressure value in the section P-0.35 kg / cm by that the cavitation neglecting the energy losses Determine the flow rate to start. Note: Use a period (.) as a decimal separator in your answers. Otherwise, even if your result is correct, it will be considered incorreet by the system. 3. Q m'/sec

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In some high-rise buildings, water is stored in an elevatedtank on the roof to minimize pressure fluctuations inthe system. Consider water that is pumped through a 10-cmsteel pipe to the roof of a 200-m-tall building; the pump ison the ground floor. For a water temperature of lOOC and aflow of 0.02 m3/s, what is the pressure at the pump discharge(in kPa)?
Question in image. i need help with q 2
q1
In a small section of a piping system, water at temperature of plastic pipe with diameter of 15cm which is placed at a upward slope of 35° as shown in Figure Ql(a). A mercury manometer is used to measure the pressure different inside the pipe. A globe valve is installed on the pipe to control the water flow rate at 0035 m³/s. is enters à Globe Mercury 3 m Figure Q1(a) If the valve is fully opened and the volume flow rate is 0.035 m³/s, determine the height of mercury manometer. (i) If the plastic pipe is replaced by cast iron pipe, evaluate the new height of the mercury manometer. (ii)
PROB E. A capillary –tube viscometer is being selected to measure viscosity of a liquid food. The maximum viscosity to be measured will be 230 cP and the maximum mass rate is 900 grams per hour. If the tube length is 10 cm and the maximum sustainable pressure is 25 Pa, determine the nominal diameter size of the tube to be used.
A pump discharges 8000 liters per minute of a certain brine solution (SG=1.20) to an evaporating pond. The intake line is 25cm in diameter and is at the same level as the pump discharge line, which is 15cm in diameter. The pressure at the inlet of the pump is -170mm of mercury. The pressure gage connected to the pipe discharge reads 150 kPa, and its center is 2.0mabove the center of the discharge flange. The vapor pressure of the brine solution is 40mm of Hg. If the pump efficiency is 80%. How much power is required?
Brine is flowing through a coil with a velocity of 240 fpm, The pressure foss in overcoming me traction in the coil 3.134 psia. The diameter of the coil is 3 ft and it has internal diameter of 1.20 inches At 86 degree Fahrenheit, the density of the brine is 995.6262 kg/m and its viscosity is 0.10081067 PA. a.) Calculate for the fanning friction factor in problem. b.) Determine the number of turns of the coil.
i need the answer quickly
a scaled tank cintaining sea water to a height of 12m also contain air above the water at gage pressure of 5 atm, water flow out from the bottom through a small hole. calculaye the efflux speed of the water, psw = 1.03x10 kg/m
(1) Given the working form of the Bernoulli equation as dW - F dm Where 3 is the friction heating per unit mass dP F = Au - dm Given also that friction heating in laminar flow of Newtonian fluids in circular pipes is given as -AP F =- = -gAz = Q Ax " 128 Ax is change in the x-direction. A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m. The flow rate is 10* m³ / s. What is the viscosity of the fluid? Typical capillary viscometer
Water is flowing in AF pipe (Figure 1) at a velocity of 2 m/s and a pressure of 102400 Pa, the pipe lengthis 100 m. If the water pressure needs to be at a pressure of 1.6 atm on a lower level. What should bethe different in elevation between the upper and lower levels in order to achieve this pressure? Takethe density of water 1000 kg/m3 and gravity is 9.81 m/s2, consider the energy loss.
liquid pentane with relative density 0.62, 20 °c as shown in the figure at temperature, the geyç pressure is 0.2 atm dollars a cast iron (0.2 m odiameter cast iron)) it flows through the pipe.Marked as full pipe output it can be considered as the principal atmospheric pressure at the point at which it is. The total pipe length in the system is 45 m.5 kW in the system there is a pump that works with 92% efficiency in its power. Liquid since the volumetric flow rate of pentane is 0.05 m2 / s, with the tank calculate the height difference botween the pipe output. Data: * Friction loss at the pump is negligible. Gryc Atark purmp