please help me in 6 1. Two wattmeters connected to measure the input to a balanced three-phase circuit indicate 2500 Wand 500 W respectively. Find the power factor of the circuit (a) when both readings are positive and (b) whenthe latter reading is obtained after reversing the connections to the current coil of one instrument.|(a) 0.655 (b) 0.3591] (City & Guilds, London)2. A 400-V, 3-phase induction motor load takes 900 kVA at a power factor of 0.707. Calculate the kVArating of the capacitor bank to raise the resultant power factor of the installation of 0.866 lagging.Find also the resultant power factor when the capacitors are in circuit and the motor load has fallen to300 kVA at 0.5 power factor.3. Two wattmeters measure the total power in three-phase circuits and are correctly connected. Onereads 4,800 W while other reads backwards. On reversing the latter, it reads 400 W. What is the total powerabsorbed by the circuit and the power factor?4. The power taken by a 3-phase, 400-V motor is measured by the two wattmeter method and thereadings of the two wattmeters are 460 and 780 watts respectively. Estimate the power factor of the motorand the line current.|296 kVA, 0.998 leading] (City & Guilds, London)[4400 W; 0.49| (Sheffield Univ. U.K.)[0.913, 1.96 AJ (City & Guilds, London)5. Two wattmeters, W, and W, connected to read the input to a three-phase induction motor runningunloaded, indicate 3 kW and 1 kW respectively. On increasing the load, the reading on W, increases whilethat on W, decreases and eventually reverses.Explain the above phenomenon and find the unloaded power and power factor of the motor.12 kW, 0.287 lag] (London Univ.)6. The power flowing in a 3-0, 3-wire, balanced-load system is measured by the two wattmetermethod. The reading on wattmeter A is 5,000 W and on wattmeter B is – 1,000 W(a) What is the power factor of the system?(b) If the voltage of the circuit is 440, what is the value of capacitance which must be introduced intoeach phase to cause the whole of the power measured to appear on wattmeter A?10.359; 5.43 (Meters and Meas. Insts. A.M.I.E.E. London)inn 1. -L-

Answered: Image /qna-images/answer/4dbfce21-44ce-4726-b208-ccc2fe2ff396.jpg

6. The power flowing in a 3-0, 3-wire, balanced-load system is measured by the two wattmeter method. The reading on wattmeter A is 5,000 W and on wattmeter B is- 1,000 W (a) What is the power factor of the system? (b) If the voltage of the circuit is 440, what is the value of capacitance which must be introduced into each phase to cause the whole of the power measured to appear on wattmeter A?

6. The power flowing in a 3-0, 3-wire, balanced-load system is measured by the two wattmeter method. The reading on wattmeter A is 5,000 W and on wattmeter B is- 1,000 W (a) What is the power factor of the system? (b) If the voltage of the circuit is 440, what is the value of capacitance which must be introduced into each phase to cause the whole of the power measured to appear on wattmeter A?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

GIVEN: Three-phase System Data: 30 Source ZLine 30 Load Ean Zan = Zbn = Zen = 0.1 + j1.5 n Source: 12020° v; Epn = 1202 – 120° v; Een = 1204120° v (grounded neutral) Line Impedance: Zline a = Zline b Zline c = 1+ j2 N; C Load Impedance: Zab 40 + j30 N; Zbc = 40 – j30 N; Zca = 50 + j0 N %3D %3D
Repeat above (insert image) with the resistors in parallel, insert multitesters (digital or analog) to measure current along each resistor. Comment on the meter readings and set up.
In two-way light switching, if you flip both of .5 :switch 1 & switch 2 at the same time (answer can be found in the 4th & 5th minutes) the bulb status will be the same as before the bulb status will be changed حدد إجابتك
The voltage drop is as we proceed from the supply end to the consumer points
Convert the following number from Gray code BCD code: 1001 Please show all the steps.
The function HOLD ON is used to avoid erase of the first figure by the second one. O FALSE O TRUE
I need the answer as soon as possible
Answers can be found at www.pearsonhighered.com/floyd. 1. The JFET is (a) a unipolar device (b) a voltage-controlled device (c) a current-controlled device (d) answers (a) and (c) (e) answers (a) and (b) 2. The channel of a JFET is between the (a) gate and drain (b) drain and source (c) gate and source (d) input and output 3. A JFET always operates with (a) the gate-to-source pn junction reverse-biased (b) the gate-to-source pn junction forward-biased (c) the drain connected to ground (d) the gate connected to the source 4. For VGs = 0 V, the drain current becomes constant when Vps exceeds (a) cutoff (b) VDD (c) Vp (d) 0 V 5. The constant-current region of a FET lies between (a) cutoff and saturation (b) cutoff and pinch-off (c) 0 and Ipss (d) pinch-off and breakdown 6. Ipss is (a) the drain current with the source shorted (b) the drain current at cutoff (c) the maximum possible drain current (d) the midpoint drain current 7. Drain current in the constant-current region increases when…
please show all steps.
can you do question iii please?
We have a room with 18 luminaires. These luminaires will be cleaned once per year at a total cost of $10 per luminaire for labor and consumables (rags, cleaning solution, scissors lift, etc. Every six years the luminaires will be re-lamped at a total cost of $60 per luminaire for lamps and other costs (labor, equipment, new lamps, etc) What is the annual cost of cleaning and re- lamping? Table 1: Coefficient of Utilization - All floor reflectances = 20% RCC- RCC- RCC- RCC- RCC- RCC- RCC- RCC - RCR 80%, RW 80%, RW 80%, RW 70%, RW 70%, RW 70%, RW 50%, RW 50%, RW - 70% -50% -30% - 70% -50% -30% -50% -30% 0.97 .97 .97 .94 .94 .94 .90 .90 1.89 .86 .82 .87 .84 .81 .80 .78 2.82 .76 .71 .80 .74 .70 .71 .68 3.75 .67 .61 .73 .66 .61 .64 .59 4.69 .60 .54 .68 .59 .53 .57 .52 5.64 .54 .47 .62 .53 .47 .52 .46 6.59 .49 .42 .58 .48 .42 .47 .41 7.55 .45 .38 .54 .44 .38 .43 .37 8.51 .41 .34 .50 .40 .34 .39 .34 9.48 .38 .31 .47 .37 .31 .36 .31 10.45 .35 .29 .44 .34 .28 .34 .28
i need the answer quickly