6. If you hold your arm outstretched with palm upward, as in the figure, the force to keep your arm from falling comes from your deltoid muscle. The arm of a typical person has mass 4.0 kg and the distances and angles shown in the Figure. a. What force must the deltoid muscle provide to keep the arm in this position? b. By what factor does this force exceed the weight of the arm? 15° Deltoid 17 cm 38 cm e201a Person Education, irc

6. If you hold your arm outstretched with palm upward, as in the figure, the force to keep your arm from falling comes from your deltoid muscle. The arm of a typical person has mass 4.0 kg and the distances and angles shown in the Figure. a. What force must the deltoid muscle provide to keep the arm in this position? b. By what factor does this force exceed the weight of the arm? 15° Deltoid 17 cm 38 cm e201a Person Education, irc

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

1. The picture shows a heavy ball held in the palm of a hand. The mass of the ball M is 7.5 kg. The lower arm is horizontal and is held by the force from the bicep Biceps muscle in the vertical upper arm. Given that the mass of the lower arm is 2.0 kg, what is the magnitude of (a) the force of the biceps muscle on the lower arm and (b) the force between the bony structures at the elbow Elbow contact contact point? point 4.0 cm Lower arm (forearm plus hand) center 15 cm Draw a free body diagram to indicate all the forces on the lower arm. And write down where is the pivot -33 cm of mass point when you calculate the torque in each part.
You’re a highway safety engineer, and you’re asked to specify bolt sizes so the traffic signal shown in the Figure below won’t fall over. The figure indicates the masses and positions of the structure’s various parts. The structure is mounted with two bolts, located symmetrically about the vertical member’s centerline, as shown. What tension force must the left-hand bolt be capable of withstanding?
The large quadriceps muscle in the upper leg terminates at its lower end in a tendon attached to the upper end of the tibia (see Figure a). The forces on the lower leg when the leg is extended are modeled as in Figure b, where T is the force of tension in the tendon, w is the force of gravity acting on the lower leg, and F is the force of gravity acting on the foot. Find T when the tendon is at an angle of 25.0° with the tibia, assuming that w = 29.0 N, F = 12.3 N, and the leg is extended at an angle ? of 40.0° with the vertical. Assume that the center of gravity of the lower leg is at its center and that the tendon attaches to the lower leg at a point one-fifth of the way down the leg. (Give the magnitude.)
Consider the following figure. A beam with a length of 3.0 m and a mass of 100 kg is held by two supports. A student with a mass of 80 kg is standing on the beam 1 m away from the second support. Determine the forces F1 and F2. F₁ 2m Wbeam W. 1m student
1 A person exercises the quadriceps as shown. The diagram on the right shows a model of the leg, where the person's lower leg of length L = 0.60 m is held at an angle 0₁ = 60° with respect to the horizontal. The quadriceps muscle exerts a force FM via the tendon that attaches to the tibia at a distance d = 0.10 m from the knee, in order to lift a weight of mass m₁ = 5.91 kg that is attached to the foot. The tendon makes an angle of 0₂ = 11.5° with respect to the tibia. 2 What is the force required to hold the weight at the position shown in the diagram? Assume the person's lower leg weighs 150 N and its centre of mass is located at a distance L/2 from the knee. Round your answer to the nearest Newton. FM M d- 02 01 m₁
A 4-m long, 150-kg steel beam is attached to a wall with one end connected to a hinge that allows the beam to rotate up and down. The other end of the beam is held in a horizontal position with a cable that makes a 27° angle with the beam and is attached to the wall (see (Figure 1)). a.What is the tension force that keeps this beam in static equilibrium? b. A mass of 75 kg is hung from the beam 3 meters away from the hinge (see (Figure 2)). Now what is the tension force that keeps this beam in static equilibrium? c.What is the vertical component of the force that the hinge exerts on the beam?
You set up a Halloween prank by attaching a small board to a hinge above your front door. The far end of the board is held up by a cable that can be released by remote control. You place a spooky spider on the board that is dropped on unsuspecting trick-or-treaters when you release the cable. The drawing below shows the set-up. cable 40° Hinge 60 ст You use a board that is 60 cm long and the cable makes an angle of 40 degrees with the board when the board is held horizontally. You place the spider a distance of r = 37 cm from the hinge. The board has a mass of 2.2 kg and the spider has a mass of 1.6 kg. The hinge applies both a horizontal force and a vertical force. You will be asked to determine the direction of both of these forces (left, right, up, down). What is the magnitude of the tension in the cable in Newtons? T = What is the magnitude and direction of the horizontal force from the hinge? Enter a positive number for the magnitude. Fh = Direction ---Select--- What is the…
In the picture to the right, the bowling ball is replace by a 23.5 N melon. a) What force does the biceps exert to hold the arm steady? b) What is the reaction force at the elbow? Equations: t = Fr^ tccw = tcw Fup = Fdown
The see-saw is balance.d What is the magnitude of the weight of the person hanging off the edge? 4m- 2m. LIST = N 11 WT-500 N
A cook holds a 2.00-kg carton of milk at arm's length must be exerted by the biceps (Fig. P8.19). What force F muscle? (Ignore the weight of the forearm.) Milk 75.0° 25.0 cm 8.00 cm Figure P8.19
Figure for Question # 18. Y 18. A uniform plank is supported by two equal 120-N forces at X and Y, as shown. The support at X is then moved to Z (half-way to the plank center). The supporting forces at Y and Z are then: * O A. F_Y=240 N, F_Z=120 N O B. F_Y=200 N, F_Z=40 N O C. F.Y=40 N, F_Z=200 N O D. F_Y=80 N, F_Z=160 N O E. F_Y=160 N, F_Z=80 N
A baseball bat balances 76.1 cm from one end. If a 0.500 kg glove is attached to that end, the balance point moves 26.7 cm toward the glove. $ % Part A Find the mass of the bat. mbat = Submit Provide Feedback 15. ΑΣΦ Search or type URL MacBook Pro Request Answer & 7 * 00 ? kg