40° cable 12 What is the magnitude of the tension in the cable in Newtons? T= N F 60 cm You use a board that is 60 cm long and the cable makes an angle of 40 degrees with the board when the board is held horizontally. You place the spider a distance of r = 40 cm from the hinge. The board has a mass of 3.1 kg and the spider has a mass of 1.3 kg. The hinge applies both a horizontal force and a vertical force. You will be asked to determine the direction of both of these forces (left, right, up, down). Hinge What is the magnitude and direction of the horizontal force from the hinge? Enter a positive number for the magnitude. Fh= N Direction --Select-- What is the magnitude and direction of the vertical force from the hinge? Enter a positive number for the magnitude. Fy= Direction --Select---

40° cable 12 What is the magnitude of the tension in the cable in Newtons? T= N F 60 cm You use a board that is 60 cm long and the cable makes an angle of 40 degrees with the board when the board is held horizontally. You place the spider a distance of r = 40 cm from the hinge. The board has a mass of 3.1 kg and the spider has a mass of 1.3 kg. The hinge applies both a horizontal force and a vertical force. You will be asked to determine the direction of both of these forces (left, right, up, down). Hinge What is the magnitude and direction of the horizontal force from the hinge? Enter a positive number for the magnitude. Fh= N Direction --Select-- What is the magnitude and direction of the vertical force from the hinge? Enter a positive number for the magnitude. Fy= Direction --Select---

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

In the figure, a horizontal scaffold, of length 2.26 m and uniform mass 59.9 kg, is suspended from a building by two cables. The scaffold has dozens of paint cans stacked on it at various points. The total mass of the paint cans in 79.9 kg. The tension in the cable at the right is 739 N. How far horizontally from that cable is the center of mass of the system of paint cans? Number i Units m
11. The diagram below shows a ladder that is 6.0 m long and has a mass of 20.0 kg. The ladder rests on a level floor and against a wall at an angle of 15° to the wall. The coefficient of static friction between the ladder and the floor is 0.232. A person with a mass of 60.0 kg begins to climb the ladder. The base of the ladder will begin to slide away from the wall when the person reaches which distance interval from the base of the ladder? A. 0 m–1.5 mB. 1.5 m–3.0 mC. 3.0 m–4.5 mD. 4.5 m–6.0 m
A window washer is standing on a scaffold supported by a vertical rope at each end. The scaffold weighs 300 N and is 4.50 m long. What is the tension in each rope when the 600-N worker stands 1.30 m from one end? Make use of the situations in this scenario and tell us a story of your own that involves a similar type of static equilibrium. You may use approximate values to solve the problem that you come up with.
How do you do this? A hungry bear weighing 700 N walks out on a beam in an attempt to retrieve a basket of goodies hanging at the end of the beam (see figure below). The beam is uniform, weighs 200 N, and is 6.00 m long, and it is supported by a wire at an angle of ? = 60.0°. The basket weighs 80.0 N. a) When the bear is at x = 1.00 m, find the tension (in N) in the wire supporting the beam and the components of the force exerted by the wall on the left end of the beam. b) If the wire can withstand a maximum tension of 875 N, what is the maximum distance (in m) the bear can walk before the wire breaks?
Problem: A 80 kg construction worker is sitting 2.0 m from the right end of a 1450 kg, 6.0 m long beam. What is the tension in the cable attached at an angle of 30 deg. from the beam? (A) Pictorial Representation (B) Physical Representation
Q3. In the figure below, one end of the uniform beam of mass 50 kg is hinged to a wall. The other end of the beam is supported by a cable that makes angles e = 30 degrees with both the wall and the beam. A box of mass 10 kg is hanged at the end of the beam with a rope. The magnitude of the forces at the hinge. Hinge rope MB=10kg cable
A horizontal 4.0 m long 10 kg uniform bar at one end is attached to a wall by a frictionless hinge and at the other end is held up by a cable that is 45 ° to the horizontal. i) What is the tension of the cable? ii)What is the magnitude of the horizontal component of the force on the bar due to the hinge?
When a person stands on tiptoe (a strenuous position), the position of the foot is as shown in Figure a. The total is supported by the force n exerted by the floor on the toes of one foot. A mechanical gravitational force on the body, F model of the situation is shown in Figure b, where T is the force exerted by the Achilles tendon on the foot and R is the force exerted by the tibia on the foot. Find the values of T, R, and 0 when F, = n = 770 N. (For 0, enter the smaller of the g' two possible values between 0° and 90°.) -Achilles tendon Tibia 15.0° 18.0 cm 25.0 cm a T = R = N = Submit Answer
Please help: A 12.8 m ladder whose weight is 200 N is placed against a smooth vertical wall. A person whose weight is 500 N stands on the ladder a distance 2.2 m up the ladder. The ladder makes an angle of 31 degrees with the vertical wall (see figure) Find the normal force exerted by the floor on the ladder.
An archer's bow is drawn at its midpoint until the tension in the string is 0.866 times the force exerted by the archer. What is the angle between the two halves of the string? Number i ! Units ° (degrees)
A 3.0-m -long ladder, as shown in (Figure 1), leans against a frictionless wall. The coefficient of static friction between the ladder and the floor is 0.50. Figure L=3.0 m 1 of 1 Part A What is the minimum angle the ladder can make with the floor without slipping? 0min = Submit VO ΑΣΦ Provide Feedback You have already submitted this answer. Enter a new answer. No credit lost. Try again. ? Previous Answers Request Answer O
Problem B3. A solid cylinder is supported on an inclined plane by a chord parallel R above the radius of the cylinder. The cylinder has a to the plane at a distance of 3 radius of 2.00 m, its mass is 20.0 kg, and the inclined plane has an inclination of 20°. The coefficient of kinetic friction between the cylinder and the plane is 0.20 and the coefficient of static friction is 0.30. The cylinder remains in static equilibrium. 20 Figure B3. Problem diagram B3 e) If the inclined surface is smooth and the rope breaks, is it possible for the cylinder to roll without sliding downhill? Clearly explain your reasoning.