1. A 16 m long beam (M = 350 kg) pinned at the bottom rises at 70° above horizontal. Its center of mass is 6 m from the bottom. It is held in place by a horizontal cable attached to the top of the beam. A vertical cable attached to the top also holds up a mass m = €600 kg. Determine the tension in each of the cables. Draw a diagram and showing the forces you are determining.

1. A 16 m long beam (M = 350 kg) pinned at the bottom rises at 70° above horizontal. Its center of mass is 6 m from the bottom. It is held in place by a horizontal cable attached to the top of the beam. A vertical cable attached to the top also holds up a mass m = €600 kg. Determine the tension in each of the cables. Draw a diagram and showing the forces you are determining.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

1 A person exercises the quadriceps as shown. The diagram on the right shows a model of the leg, where the person's lower leg of length L = 0.60 m is held at an angle 0₁ = 60° with respect to the horizontal. The quadriceps muscle exerts a force FM via the tendon that attaches to the tibia at a distance d = 0.10 m from the knee, in order to lift a weight of mass m₁ = 5.91 kg that is attached to the foot. The tendon makes an angle of 0₂ = 11.5° with respect to the tibia. 2 What is the force required to hold the weight at the position shown in the diagram? Assume the person's lower leg weighs 150 N and its centre of mass is located at a distance L/2 from the knee. Round your answer to the nearest Newton. FM M d- 02 01 m₁
A 4-m long, 150-kg steel beam is attached to a wall with one end connected to a hinge that allows the beam to rotate up and down. The other end of the beam is held in a horizontal position with a cable that makes a 27° angle with the beam and is attached to the wall (see (Figure 1)). a.What is the tension force that keeps this beam in static equilibrium? b. A mass of 75 kg is hung from the beam 3 meters away from the hinge (see (Figure 2)). Now what is the tension force that keeps this beam in static equilibrium? c.What is the vertical component of the force that the hinge exerts on the beam?
A block of mass MB=2.5 kg is attached to a pulley of mass MP=2MB and R=10.0 cm (Icyl = 1/2MR2) and is pulled from the other side with force F=30.6 N with a massless string as in Figure 3. A. Write an expression for Newton's 2nd Law for the block. B. Write an expression for Newton's 2nd Law (for torque) for the pulley. C. Calculate the acceleration of the system and indicate the direction.
A 14.0 m uniform ladder weighing 510 N rests against a frictionless wall. The ladder makes a 59.0°-angle with the horizontal. A. Find the horizontal and vertical forces (in N) the ground exerts on the base of the ladder when an 810-N firefighter has climbed 4.10 m along the ladder from the bottom. B. If the ladder is just on the verge of slipping when the firefighter is 9.40 m from the bottom, what is the coefficient of static friction between ladder and ground? C. If oil is spilled on the ground, causing the coefficient of static friction to drop to half the value found in part (b), what is the maximum distance (in m) the firefighter can climb along the ladder from the bottom before the ladder slips?
17 kg uniform store sign is held from a uniform horizontal beam as shown. There is a cable attached to the right edge of the beam and is secured to the wall, 250 cm above where the beam meets the wall. The sign is symmetrically suspended by two cords, the left cord being 80 cm from the wall, and the cord on the right being at the right edge of the beam, 200 cm from the wall. a. What is the tension in the left and right cords that hold the sign? b. What is the tension in the cable? c. What is the horizontal component of the force that the wall exerts on the beam?
A purple beam is hinged to a wall to hold up a blue sign. The beam has a mass of mp = 6.2 kg and the sign has a mass of mg = 17.3 kg. The length of the beam is L = 2.55 m. The sign is attached at the very end of the beam, but the horizontal wire holding up the beam is attached 2/3 of the way to the end of the beam. The angle the wire makes with the beam is 0 = 34.2°.
A 164-cm-tall person lies on a light (massless) board which is supported by two scales, one under the top of her head and one beneath the bottom of her feet. The two scales read, respectively, 35.1 and 31.6 kg. (Figure 1) Part A What distance is the center of gravity of this person from the bottom of her feet? Express your answer to three significant figures and include the appropriate units. d = for Part A for Party do for Part redo fo Part A reser for Part A keyboard shortcuts for Part A Value Units
26
A 3.0-m -long ladder, as shown in (Figure 1), leans against a frictionless wall. The coefficient of static friction between the ladder and the floor is 0.50. Figure L=3.0 m 1 of 1 Part A What is the minimum angle the ladder can make with the floor without slipping? 0min = Submit VO ΑΣΦ Provide Feedback You have already submitted this answer. Enter a new answer. No credit lost. Try again. ? Previous Answers Request Answer O
1. A 160kg utility pole extends 12.0m above the ground. A horizontal force of 250N acts at its top and the pole is held in the vertical position by a cable. a. Draw a free-body (or force) diagram for the pole. b. Determine the tension in the cable. c. What are the reaction forces exerted at the lower end of the pole by the ground? 2. A 40.0kg uniform platform is suspended by two cables, 2.00m apart, where the centre of the platform lies midway between the cables. A 5.00kg paint bucket is placed on the platform, 24.0cm to the right of the right cable. Determine the tension in each cable.
A painter stands on a uniform horizontal beam of length L = 6.0 m that is held in equilibrium by support cables attached to the roof as shown in Figure 3. The beam has a weight Wb = 250.0 N and the tensions on the left and the right ends are measured to be Tl = 360.0 N and Tl = 200.0 N respectively. A. Calculate the weight of the painter Wp , and Wb. the distance x where the painter is standing.