6. A bronze spherical shell of thickness 15 mm is installed in a chemical plant. The shell is subjected to an internal pressure of 1 N/mm2. Find the diameter of the shell, if the permissible stress for the bronze is 55 MPa. The efficiency may be taken as 80%. [Ans. 2.64 m]

6. A bronze spherical shell of thickness 15 mm is installed in a chemical plant. The shell is subjected to an internal pressure of 1 N/mm2. Find the diameter of the shell, if the permissible stress for the bronze is 55 MPa. The efficiency may be taken as 80%. [Ans. 2.64 m]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: what is the formula used in the -δp + δt = -δp + δt = -δp + δt part at the top? what is the…

A: Given: (-δp + δt)A = (-δp + δt)B = (-δp + δt)C Required: To explain the δp and δt meaning in the…

Q: Example: the low cycle fatigue of a certain steel is given by life cycle equation-2: (of/E)=0.005…

A: The fatigue strength of steel /Modulus of elasticity(E), The fatigue Ductility coefficient is, The…

Q: A metal bar of length 100mm is inserted between two rigid supports and its temperature is increased…

A: Given data- Length of the bar L=100 mmIncrease in temperature∆T=10oCCoefficient of thermal expansion…

Q: A cylindrical boiler with an outside diameter of 3.60 m and a wall thickness of 40 mm is made of a…

Q: An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top…

A: Calculate the shear stress and shear strain. Then using Hookes law the value of shear modulus can be…

Q: Another of the steel components manufactured by michael's company is steel railway track sections.…

A: Given: Length of the steel track component at the initial temperature, L = 120 m Initial…

Q: . An element whose material has Sy = 280 MPa, Sut= 330 MPa, and Suc= 460 MPa is loaded as shown.…

Q: As an engineer you are asked to evaluate the feasibility of a device which operates in a temperature…

A: Given, E = 70 GPa or 70000 MPa σmax = 100 MPa

Q: At room temperature (200C) a 0.50mm gap exists between the ends of the rods shown. At a later time…

Q: ne solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C.…

A: T=15.5kip in

Q: 8.11 SizN4 has a surface energy equal to 30 J/m? and an atomic spacing ao = 0.2 nm. Calculate the…

Q: A spherical steel pressure vessel (diameter500 mm, thickness 10 mm) is coated with brittle…

A: Step 1: Stress= E.Ɛ P = 2.05 x 10^5 x 150 X 10-6= 30 GPa Hoop stress = pd/2t = 30x0.5/2 x0.01 =750…

Q: An aluminum pipe has a length of 53 m at a temperature of 7°C. An adjacent steel pipe at the same…

Q: A metal bar of length 100mm is inserted between two rigid supports and its temperature is increased…

Q: A thin cylindrical shell made of mild steel plate is 1000 mm in diameter. It is to be subjected to…

Q: :Hardness of Gypsum is more than hardness of Diamond O Talk O Calcite O :The ratio of volume of…

A: to solve - given multiple Choice questions

Q: Determine the Basquin's law equation for the alloy. Use the following fatigue data, (about a…

Q: For the punching operation shown in the figure, compute the shear stress in the material if a force…

Q: show solution of: A liquid compressed in a container has a volume of 1 liter at a pressure of 1 MPa…

Q: copy

A: All of the following given options are true a)brinells Test-it is used to measure materials…

Q: Answer by true or false for the following The impurities in mixing water improve the durability.…

A: The strength & durability of concrete may be reduced due to the presence of impurities in mixing…

Q: of 6.0 Mpa and a tempe

Q: An engineer is laying out a design for a ceramic component whose volume is 30.3 mm. In the processes…

A: Weibull modulus = 9.5Characteristic strength = 628Volume of reference sample =5.3 mm3If the maximum…

Q: A 10-mm-diameter Brinell hardness indenter produced an indentation 1.55 mm in diameter in a steel…

Q: An alumun um rod 22 cm diameter is screwed at the ends, and passes through a steel tube 2.5 cm…

Q: assembly consists of a brass shell (1) fully bonded to a ceramic core (2). The brass shell [E = 86…

Q: If the gauge is made of a material having a yield stress equal 200 MPa, determine the minimum…

A: The given data is shown below:

Q: A rectangular nylon [E = 8 GPa; ?= 0.35; ?= 24 x107 P/°C] plate has a circular hole in its center.…

A: Young's modulus, E = 8 GPaThermal coefficient, Intial temperature = 15CFinal temperature =…

Q: Calculate total hardness in ppm of a solution of both 55 mg/L Al2(SO4)3 and 45 mg/L Mg(NO3)2

Q: A rolled brass rod and a steel rod are secured to unyielding supports. Determine the temperature…

Q: 15. With the decrease in the viscosity, Reynolds number

A: To find : What will happen to Reynolds number if viscosity will be decreased.

Q: In a compression test and for a very ductile material similar to copper , the diameter and the…

A: Initial length Lo = 80 mm Initial diameter Do = 60 mm Final diameter D = 120 mm Final length = ?

Q: Example: the low cycle fatigue of a certain steel is given by life cycle equation-2: (of/E)-0.005…

A: Solution: Given Data: Fatigue strength coefficientSfModulus of ElasticityE=0.005Fatigue strngth…

Q: A metal bar of length 100 mm is inserted between two rigid supports and its temperature is increased…

A: A metal bar between two rigid supports with the below data is given-To Find-The value of the stress…

Q: A boiler of 1.6 m diameter is made of a 20-mm thick plate. What will be the permissible steam…

A: Diameter of the boiler d=1.6 m, The thickness of the plate t=20 mm, Maximum tensile stress in the…

Q: A 0.35-m long steel rod with a round cross-section (25 mm) is resting on a frictionless surface. The…

A: The given data is: Length of steel rod (L) = 0.35 m Diameter of steel rod (d) = 25 mm Coefficient of…

Question

6. A bronze spherical shell of thickness 15 mm is installed in a chemical plant. The
shell is subjected to an internal pressure of 1 N/mm2. Find the diameter of the
shell, if the permissible stress for the bronze is 55 MPa. The efficiency may be
taken as 80%. [Ans. 2.64 m]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Solution

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Ca+2 = 36.8mg/L Mg+2 = 2.9mg/L HCO3 = 98mg/L pH = 7.53 Temp = 9C Calculate the following: a. Hardness in units of mg/L as CaCO3 b. Ionic strength (be sure to include H++ and OH--) c. PCO2 in equilibrium with the sample d. Saturation index with respect to calcite (SIC) e. Saturation index with respect to dolomite (SID)
A thin cylinder of internal diameter 1 m and thickness 0.02 m contains a gas. The tensile stress in the material is not to exceed 100 MPa then determine the internal pressure of the gas
Two similar bars of Steel and Aluminium are heated to a same temperature. Forces are applied at the ends of the bars to maintain their lengths unaltered. If the ratio of Young's moduli of Steel and Aluminium is 3, and the ratio of the coefficients of thermal expansion of Steel to that of Aluminium is 0.5, what is the stress on the Aluminium bar if the stress on the Steel bar is 100 MPa?
asap
What is the ratio of the strain energy in bar X to that in bar Y when the material of the two bars is the same? The cross-sectional areas are as indicated over the indicated lengths.
At a temperature of 80°C, a copper tire 12 mm thick and 90 mm wide that is to be shrunk onto a locomotive driving wheel 2 m in diameter just fits over the wheel, which is at a temperature of 25°C. Determine the contact pressure between the tire and wheel after the assembly cools to 25°C. Neglect the deformation of the wheel caused by the pressure of the tire.
When the exponential trend line of iron concentration vs time is y=4.2 exp(-0.24x) x is time in min and y is concentration of phen iron complex solution.
Mechanics of deformable bodies -Write complete solution
Describe the basic properties of Montmorillonite.
Please solve both.
When a bar is cooled to -5°C, it will develop O(A) No stress OCB) Shear stress OC) Tensile stress O(D) Compressive stress
A steel rod is fixed at one end and the other end has a distance of 0.2 mm from a rigid support. The rod is heated to increase its temperature by 200°C. Calculate the stress developed in the rod. The elastic modulus of rod is 200 GPa and the coefficient of thermal expansion is 104per °C.