6 : The elastic limit of copper is 1.5 x 10' N/m². Find the maximum radius of the copper wire must have, if its elastic limit is not be exceeded under load of 10 kg (g = 9.8 m/s?) %3D
Q: Spiderweb An orb weaver spider with a mass of 0.25 g hangs vertically by one of its threads. The…
A: a)The required fractional increase in length is,
Q: A hanging wire made of an alloy of iron with diameter 0.09 cm is initially 2.2 m long. When a 66 kg…
A:
Q: A T-section thin-walled beam which is used as a cross member of a ladder frame chassis is subjected…
A: Given Sy = 10 kN h = 100 mm t = 2 mm Find, the expressions for the shear flow distribution in…
Q: A circular metal column is to support load of 500 Tonne and it must not compress more than 0.1 mm.…
A:
Q: A road engineer is planning to build an overpass and wants to support a 2.1 × 10° kg load over a…
A: Given that, Length of the column is L = 5.450 m Diameter of the column is d = 73.60 cm = 0.736 m…
Q: 1. A steel wire of length 4.7 m and cross section 3.0 x 10 m2 stretches by the same amount as a…
A:
Q: 4. A steel shaft 4 ft long that has a diameter of 5 in is subjected to a torque of 20 kip-ft. Use a…
A: In this question we need to find 1st formula for maximum shearing stress then find the angle of…
Q: 4. A 5.0 inches cube chiffon cake on a table was exposed to a shearing force of 0.20 The upper…
A: Given-The shear modulus of the cake is G=0.05 lb/in2Slide of chiffon l=5 inchesShearing force…
Q: 5. For a linear viscoelastic material, assume its = 3 seconds, T = 31 seconds, ER = 150 MPa, please…
A:
Q: 0.3 m /TM 10 kg 0.3 m /TM 5 kg
A: Given data m1=5 kgm2=10 kgA=0.05 m2Y=1.1×1011 N/m2 When a weight is suspended through a wire a…
Q: Q5) A aluminum bar (E(STRESS/STAIN)=68.9 GPa) has a circular cross section and is 15m long.…
A:
Q: 3. A flat steel bar 150 mm wide by 50 mm thick has axial loads applied at points A, B, C and D as…
A: Solution: The free-body diagram of the forces of the bar in section BC is shown in the figure.
Q: Determine the strain-stress relations of an isotropic material for a cylindrical coordinate system.
A:
Q: D 14 mm 300 mm| E B - 300 mm 3 mm 3 mm
A: Concept used: Strain is the ratio change in length (increase or decrease) to original length. The…
Q: A tensile stress is to be applied along the axis of a cylindrical brass rod with diameter of 15 mm.…
A: The lateral strain is, εx=∆dd0 =-3.5×10-215×10-3 =-2.33 The axial strain is, εz=-εxν…
Q: 5-77. The steel shaft has a diameter of 40 mm and is fixed at its ends A and B. If it is subjected…
A: Diameter of steel shaft , d = 40mm The applied force, F= 3kN Rigidity modulus of the shaft, Gst =…
Q: Artificial diamonds can be made by putting carbon in high-pressure high-temperature presses. Suppose…
A: Given:pressure = 6 GPa.Bulk modulus = 194 GPaVolume,v=1ccwhen you realease the pressure bring it…
Q: 32) A steel wire, 3.2 m long, has a diameter of 1.2 mm. The wire stretches 1.6 mm when it bears a…
A:
Q: The radius of a copper 4 mm. What force is required to stretch the wire by 20% of its length,…
A: To find-Force required (F)=?Given-Elastic limit is not exceeded.Radius of copper wire (r)=4 mm…
Q: A cubic industrial material whose one side is of length 2.0 cm has a bulk modulus of 4.7 x 10^5…
A:
Q: Q2: The 20-mm-diameter bolt fastens two wooden planks together. Find the smallest thickness of cach…
A: Given, Diameter is 20 mm and working bearing stress for wood is 13 MPa
Q: 2. A tubular aluminium bar of a square cross section with outside dimensions of 50 mm x 30 mm,…
A: Given that Torque,T=300 Nm shear stress,S=20 MPa=20×106 Pa Allowable rate of twist,θ=0.025 rad/m…
Q: 2. The puncher is to drive a 25 mm diameter hole to a steel plate. If the allowable axial stress of…
A: Given, diameter= 25 mm Axial stress = 101.85 MPa The maximum shear stress= 50 mm
Q: c) A tensile stress is to be applied along the long axis of a cylindrical brass rod that has a…
A:
Q: The change in the relative configuration of point within a solid is called strain
A: In the given question we have to discuss about the strain.
Q: Q2/ The equation of a velocity distribution over a plate is u=1/3 y - y' in which the velocity in…
A:
Q: d) A cylindrical rod 100 mm long and having a diameter of 10 mm is to be defomed using a tensile…
A: According to the following question, this question ask us that, we have to examine the four alloys…
Q: B/ A four fifth meter long steel pipe has an inside and outside diameter of 24 mm and 30 mm…
A:
Q: The dimensions of the Shear Strain is Select one: O a. MLT-2 O b. MLT-1 O c. dimensionless O d.…
A:
Q: Problem 4: For the bar and loading condition shown below, determine (a) the radius of curvature, p…
A: Angle, radius of curvature can be calculated once we find bending moment and moment of inertia. It…
Q: iron -140 cm steel 70 cm Henry has a rod that is made out of 2 parts. An iron and steel section. The…
A: Solution: Given: 1 m = 103 mm L1 = length of iron section = 40 cm = 0.40 m L2 = length of steel…
Q: A square flat plate of dimensions 1 m x 1 m is moving with a maximum speed , U causing a fully…
A: The given values are, A=1 m×1 m=1 m2ρ=1.2 kg/m3υ=1.5×10-5 m2/s
Q: Question 9 of 10 Determine the forces in members BC and CF of the loaded truss. Enter a positive…
A: Solution:-The free body diagram of the lower half section is shown below. Here ,FBC is the force…
Q: Question 3 A balcony weighs 100 kN and is supported by four circular steel cables with an equal…
A:
Q: A steel rope of 2.00 m in length is pulled about 0.30 cm. The diameter of the rope is 0.20 cm.…
A: Length of the steel rope Pulled length Diameter of the rope Young's modulus of the steel
Q: 1. Consider the brass alloy for which the stress-strain behavior is a cylindrical specimen of this…
A:
Q: 49 : If a pressure of 8 x 10* N/m2 is applied to a lead block so that its volume reduces by 20°o,…
A: Given : Pressure (dP)=8×108 N/m2Reduction in volume dV=20 % of V=20100v To find : Bulk…
Step by step
Solved in 2 steps