Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each plankes if the working bearing stress for wood is 13 MPa. Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of cachplankes if the working bearing stress for wood is 13 MPa.20 mm

Given, Diameter is 20 mm and working bearing stress for wood is 13 MPa

Answered: Q2: The 20-mm-diameter bolt fastens two…

Q2: The 20-mm-diameter bolt fastens two wooden planks together. Find the smallest thickness of cach plankes if the working bearing stress for wood is 13 MPa. 20 mm

Related questions

Q: A plastic board with length X and mass Y is leaning against a frictionless wall. The plastic b. made…

A: Given data: The length of the plastic board is l=X unit. The mass of the plastic board is m=Y unit.…

Q: D 10 cm 30° M C B 20 cm Quest The allowable tension and compression stresses are given as: gtension…

Q: A circular rod of cross-sectional area 2 x 104m² has a tensile force of 80 kN app The stress in the…

Q: 3. A long steel wire hanging from a balloon carries a weight W at its lower end (see figure). The…

Q: Q2 The structure shown in the following figure is made up of three blocks. No pin or other…

Q: A circular rod of cross-sectional area 2 x 10m² has a tensile force of 80 kN applied to it. The…

Q: The homogeneous wire ABCD is bent as shown and is attach to a hinge at C. Determine the length L…

A: this question is about to measure center of gravity of wire for equilibrium.

Q: Determine the largest weight W that can be supported by two wires shown in Fig. The stress in either…

A: Maximum weight supported by the given system of wires is equal to the sum of vertical components of…

Q: For the beam and loads shown in the figures: 1.-Draw the shear force and bending moment diagrams.…

A: Solution:-Given thatP=70 kNQ=P2-6=702-6=29 kNR=Q2=14.5 kN

Q: 10 lb 7 lb w=3lb/ft What is the value of the shear at point a? What is the value of the shear at…

Q: The beam is subjected to the distributed load and the couple shown. If M is slowly increased…

Q: maximum shear = 60 MPa and modulus of rigidity = 77 GPa. Basing from the angle of twist determine…

Q: a. Two strips of metal are pinned together as shown, with a rod of 10mm diameter. The Ultimate shear…

Q: A force stretches a (first) wire by 2mm. This wire is made of an unknown material and has a 1.2cm…

A: Given quantities: diameter of the first wire (D) = 1.2 cm length of the first wire (L) = 3.5 cm…

Q: Figure 305 H Cylinder #3, diameter = 8m 10m cable 6m PROBLEM SP305 In figure 305, a load is…

A: Solution: The angle made by the cable with the boom is, tanθ=68θ=37° Let T be the tension in the…

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

Q: How much will a steel wire 2 m long and 1 mm diameter stretch under a 5 kg. wt. load? (Y=2 x 10"…

A: Length of the steel wire, L=2 m Diameter, d=1 mm radius, r=0.5 mm=0.0005 m Young's modulus, Y=2×1011…

Q: Example 10.22 Compare the loads required to produce equal depressions for two beams made of the same…

Q: 1. A homogeneous 800 kg bar AB is supported at either end by a cable as shown in the figure. Bronze…

Q: beyond the maximu Fter some time?

A: Given: What happens when the stress applied to the body is increased beyond the maximum value and is…

Q: Question 7. The following true stress-strain curve for a carbon nanofiber/epoxy with CaCO3…

A: Formula be used σ=kεnσ is a true stressε is a true straink and n are constant From the graph we get…

Q: The dimensions of the Tensile Stress is Select one: O a. MLT-1 O b. ML2T-2 O c. MLT-2 O d. ML-1T-2 O…

Q: .a 2.11x106 N/m² .b 2.2x106 N/m2 .c 2.02x106 N/m² .d

A: trabecular bone tissue is a network of the solid bone tissue.trabecular bone has lower calcium…

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

Q: Why must a water skier moving with constant velocity lean backward? What determines how far back she…

A: The free-body diagram for the skier moving at constant velocity leaning backwards is given as,

Q: A walkway suspended across a hotel lobby is supported at numerous points along its edges by a…

A: Given info: Before loading, the diameter of the steel cable is 1.27 cm and the length of the steel…

Q: A medical technician uses a pair of 0.125m long tweezers to remove a wood sliver from a patient. The…

A: What is the mechanical advantage?

Q: Fac = 60 lbf E 25 6 ft 15* 24 W = 215 Ibf

A: Force is a vector quantity defined as the rate of change in the momentum of an object as defined by…

Q: А В 40° D 500 mm 200 mm

Q: QUESTION 17 (a) Calculate reactions at A and B in beam shown in Figure Q17 (b) Determine the…

A: Since the system is in the equilibrium, therefore the net moment at point A will be zero. Therefore…

Q: of the stud is under compression, and which surface is under tensi op and bottom surfaces are under…

A: The bending can be shown as,

Q: wire has a cross sectional area ‘A’, length ‘L’ and young’s modulus ‘Y’. It is pulled by a force ‘F’…

A: Given: Cross-sectional area = ‘A’, length = ‘L’ young’s modulus = Y It is pulled by a force ‘F’…

Q: You measure the mass (m) and physiological cross-sectional area (PCSA) of two muscles: Which…

A: The force that a muscle can produce is directly proportional to its physiological cross-sectional…

Q: The rigid beam AB is subjected to a varied force10kN and is supported by a steel rod of 17 mm…

Q: tensile test

A: Tensile test is used to see stress upon material.

Question

Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each plankes if the working bearing stress for wood is 13 MPa.