6 Part 2 of 2 ! Required Information Consider a 3.4 m thick section of dam and water. The density of the dam is 2400 kg/m³, and the density of water is 1000 kg/m³. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 1m 2m A 2m Determine the normal force and friction force between the dam and foundation, specify the distance from point A to the location of this force system, and determine the minimum value of the coefficient of friction so the dam does not slide. (Round the final answers to four decimal places.) The normal force is 176.77 KN. The friction force between the dam and foundation is 16.677 KN. The distance from point A to the location of this force system is 0.729 The minimum value of the coefficient of friction is 0.0943 ✔ m.

6 Part 2 of 2 ! Required Information Consider a 3.4 m thick section of dam and water. The density of the dam is 2400 kg/m³, and the density of water is 1000 kg/m³. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 1m 2m A 2m Determine the normal force and friction force between the dam and foundation, specify the distance from point A to the location of this force system, and determine the minimum value of the coefficient of friction so the dam does not slide. (Round the final answers to four decimal places.) The normal force is 176.77 KN. The friction force between the dam and foundation is 16.677 KN. The distance from point A to the location of this force system is 0.729 The minimum value of the coefficient of friction is 0.0943 ✔ m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow circular tube is subjected to a tension force of 30 KN, a tensile stress of 20 MPa was recorded.lf the outer diameter of the tube is 100 mm, the inner diameter will be eqaual to. a. 93.95 mm O b. 89.95 mm C. 85.95 mm o d. 91.95 mm
Calculate Tension BD if P = 100 kN. ... 2.5 m 250 N 1.5 m- 2 m- -1.5 m-
The shaft is supported by smooth journal bearings at A and B that only exert vertical reactions on the shaft. (Figure 1) Part A If d = 98 mm , determine the absolute maximum bending stress in the beam. Express your answer to three significant figures and include the appropriate units. HẢ ? Figure Value Units Omar = Submit Request Answer 12 kN/m Provide Feedback B_ 3 m 1.5 m
Course/Year/Section: A hollow steel tube with an outside diameter of 150mm must carry a tensile load of 400kN as shown in the figure. Determine the thickness of the tube if the stress is limited to 200MPa. O! 400KN d 150mm
A wooden beam carries the loading shown. Determine the smallest allowable width b of the beam if the working stress in bending is 10 MPa. 2 kN/m 5 kN yox 200 mm B 1.0 m 2m 1.0 m C
1. *A propped cantilever has a 2m overhang. The beam has a load of 2W applied half way between the fixed support and the roller support and a load of W applied at the free end. What is the minimum value of W that will cause the beam to collapse? The beam has the cross-section shown below. The yield stress is 300 MPa. 75 mm 15 mm 300 mm 2W C D 15 mm 250 mm 15 mm, 2m B + 2m 2m
Consider the beam shown in the figure. a. Determine the Maximum Tensile Flexural Stress. b. Determine the Maximum Vertical Shear Stress. 20KN/m ↓ ↓ ↓ 2M ↑ Com 200mm 200m ↓ 기 200mm 2m ] [ 20AM
A thin cylinder of inner radius 725 mm and thickness 5mm subjected to an internal pressure of 6Mpa. Find average circumferential stress?
Situation X: Consider the figure below. Wi = 200 kN/m w2 = 300 kN/m = 2m L1 L2 = 3 m L3 = 2 m W2 W1 L1 L2 L3 Batangas State University CE 420: Comprehensive Exam | Page 4 Test Bank: Engineering Mechanics Principle of Structural Analysis and Design 25. Calculate the total length, L( m), so that the resulting stress q is uniform. А. 10 В. 12 C. 9 D. 8 26. Which of the following gives the location (m) of the maximum shear from the left end? А. 4.0 В. 5.0 C. 6.0 D. 4.5 27. Which of the following gives the location (m) of the point of inflection from the left end? А. 1.24 В. 5.16 C. 6.28 D. 3.20
A 500 N block is resting on an inclined plane. See figure below. coefficient of static friction, 0.3, coefficient of kinetic friction, µk 0.2 1. Find the minimum value of P necessary to have an impending motion if 0 = 30°. W 2. Find the maximum value of P to ils = 0.3 necessary have an impending motion if 0 = 30°. %3D = 0.2 3. Find the value P that will still make the block in equilibrium condition.
Topic: Strema A 750-mm high cylinder carries a load P which produces a normal stress at its cross-sectional area and a shear stress at its lateral surface area. Find its diameter if these stresses are equal. Choices: A. 3.0 m B. 4.5 m C. 1.5 m D. 6.0 m
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E 200, 000MPa and a = 11.7- m C" Neglect bending of the beam. A=640mm2 A=320mm2 A C D 1.2m 0.8 m 1.2 m 54KN What is the stress of rod B if there is no change in temperature in MPa?