6 m A cylindrical pressure vessel contains a gas at a pressure of 6.0 MPa. The cylinder, which has an inner radius of 1200 mm and a wall thickness of 20 mm, is fabricated from steel [E = 200GP%; v = 0.30]. The cylindrical portion is 6 m long, ignore the hemispherical end- caps of the tank. corresponding strains in the tank. Using Hooke's Law, determine the MPa Onoop MPа Olong με Elong με Enoop

6 m A cylindrical pressure vessel contains a gas at a pressure of 6.0 MPa. The cylinder, which has an inner radius of 1200 mm and a wall thickness of 20 mm, is fabricated from steel [E = 200GP%; v = 0.30]. The cylindrical portion is 6 m long, ignore the hemispherical end- caps of the tank. corresponding strains in the tank. Using Hooke's Law, determine the MPa Onoop MPа Olong με Elong με Enoop

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bronze bar 2.72 m long with a cross-sectional area of 496 mm2 is placed between two rigid walls. At a temperature of 8.61 °C, there is a gap Δ = 2.28 mm, as shown in the figure. Find the compressive force (in N) experienced by the bar at a temperature of 61.85 °C. Use α = 18 × 10-6 /°C and E = 80.84 GPa. Round off your answer to three decimal places.
An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0x10-6/°C] pipe is subjected to a tensile load P. The pipe has an outside diameter of D = 280 mm, a cross-sectional area of A = 7550 mm², and a length of L = 9.5 m. The initial longitudinal normal strain in the pipe is zero. After load P is applied and the temperature of the pipe has been increased by AT = 40°C, the longitudinal normal strain in the pipe is found to be 2260 με. Calculate the magnitude of load P. Answer: P = M. L kN D P
Thank you!! Calculate the maximum tensile stress in a plate subjected to a remote loading of P. The plate has a central hole as shown below. The stress concentration at the hole is 2.5 based on the remote average stress. The Plate thickness is 1cm, plate width 20 cm and the total load P is 25 kN. Identify the location of the maximum stress at B
A brass pipe has an internal diameter of 400mm and a metal thickness of 6mm. A single layer of high tensile wire of diameter 3mm is wound closely around it at a tension of 500N. Find the stress in the pipe when there is no internal pressure. (b) the maximum permissible internal pressure in the pipe if the working tensile stress in the brass is 60MN/m^2. (c)) The stress in the steel wire under condition b. Treat the pipe as thin cylinder and neglect longitudinal stresses and strains. Young mudulus of steel=200GN/m^2 and for brass =100GN/m^2
In a hydraulic press a 690-liter volume of oil is subjected to a 6666-psi pressure increase. If the compressibility of oil is 2.0×10−5/atm,, find the bulk strain and the absolute decrease in the volume of oil when the press is operating.
Pressure inside the cylinder is 10 bars Is this a thin walled cylinder when the thickness is 10 mm. Estimate theoretically the hoop andlongitudinal stresses
1.6-7 A wire of length L = 2.5 m and diameter d = 1.6 mm is stretched by tensile forces P = 600 N. The wire is made of a copper alloy having a stress- strain relationship that may be described mathemat- ically by 124,020ɛ 0 s8s 0.03 (o = MPa) 1+ 300ɛ in which e is nondimensional and o has units of MPa. (a) Construct a stress-strain diagram for the material. (b) Determine the elongation of the wire due to the forces P. (c) If the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Last 2
A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1 m long. It is found to change in internal volume by 12.0 × 10-6 m³ when filled with a liquid at a pressure p. If E=200 GN/m² and v = 0.25, and assuming rigid end plates, determine: (a) the values of hoop and longitudinal stresses; (b) the modifications to these values if joint efficiencies of 45% (hoop) and 85% (longitudinal) are assumed; (c) the necessary change in pressure p to produce a further increase in internal volume of 15%. The liquid may be assumed incompressible.
A circular bar of length 400 mm and tapering uniformly from 50 mm to 25 mm diameter is held between rigid supports at the ends. Calculate the maximum and minimum stress developed in the bar when the temperature is raised by 30°C. Take E = 2 × 105 N/mm² and a = 1.2 x 10-5. per °c
A steel (E=210 GPa, v=0.32) cylindrical vessel has a diameter R= 25 cm, thickness t=0.2 cm and length L=100 cm. What is the increase in the length of this vessel if it is subject to PR PR. an internal pressure P kPa (unit in kPa)? (Remember: o, =
The tank shown in Figure below is fabricated from t = 1/8 in steel plate. The maximum longitudinal and circumferential stress caused by an internal pressure of 125 psi (Ib/in²). 1. Drive the expressions for longitudinal and tangentional stresses? 2. Calculate the maximum longitudinal and circumferential stress caused by an internal pressure? Fw Fw Fp Fp XLV 1.5 ft |1= 1/8 in Fw Fw Fw Fw 0.75 ft LONGITUDINAL STRESS, ₁ TANGENTIAL STRESS , 2 ft 1.5ft ث إضافة ملف