6 m -1.5 m 2 m m 2.5 m The balloon shown in the figure is being held in place by the hooks placed in B, C, and D. If F = 495 N, determine the tension in cable AB (in N). ROUND OFF TO TWO DECIMAL PLACES.

6 m -1.5 m 2 m m 2.5 m The balloon shown in the figure is being held in place by the hooks placed in B, C, and D. If F = 495 N, determine the tension in cable AB (in N). ROUND OFF TO TWO DECIMAL PLACES.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 509.9N horizontal steel shaft is suspended by a vertical cable from A and by a second cable BC which lies in a vertical transverse plane and loops underneath the shaft. Calculate the tension T1 (N) in the cable. Round off only on the final answer expressed in 3 decimal places.
The Resultant of the concurrent forces in the figure below is R = 201 KN, pointing up along y-axis. Compute the value of 0 in degrees to give this resultant. P1 = 470 and P2 = 205. Write the numerical value only and use two decimal places. P1 y1 R I+Y x1 30° F Two cables are tied together at C and loaded as shown. Determine the tension in cable AC in KN. P = 3.71 KN, x1 = 6.0 m, x2 = 5.9 m, y1 = 5.0 m, and y2 = 4.0 m. Write numerical value only and in 2 decimal places. B A 2 m P2 + X C P x2 y2
A boom consists of a 100-mm-diameter steel pipe AB and a cable BC as shown in the figure. The modulus of B P -3.6 m PROB. 17.4 1.5 m A steel E 200 X 106 kPa. Determine the capacity P of the boom. Use the Euler formula with a factor of safety of 3. Neglect the weight of the pipe. Section properties of pipe: A = 2.05 x 10³ mm² and the radius of gyra- tion r = 38.4 mm.
A frictionless pulley system is designed as shown. The diagram represents the system in static equilibrium. If theta=35deg, and the weight of the block W=685lbs. What is the tension in the cable?
A oil rig tower is held in equilibrium by three ropes. The tension in cable AD is tightened until it reaches 7600 N. B d3 da ds do d₁ d2 Z E D d5 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 8.5 m d₂ 18.5 m 16.5 m 30 m 9 m 80 m a. Determine the magnitude of the force/tension in cord AB, TAB. b. Determine the magnitude of the force/tension in cord AC, TAC. c. Determine the magnitude of the force developed along the tower, FAE- → i. Hint: FAB= (0+03+ FAER) KN. Round your final answers to 3 significant digits/figures. The magnitude of the force/tension in cord TAB is The magnitude of the force/tension in cord TAC is The magnitude of the force developed along the tower FAB is kN kN kN
B The two blocks shown are originally at rest. Neglecting the masses of the pulleys determine the tension in the cable. Given: . • Weight of block A = 220 lbs Weight of block B = 190 lbs • kinetic friction coefficient = 0.55 Find: A • Tension in cable = lbs Your Answer:
The 40-kg cylinder is suspended from a clamping collar at C which can be positioned at any horizontal position x between the fixed supports at A and B. The cable is 11 m in length. Determine and plot the tensions in cable segments AC and BC as a function of x over the interval 0 ≤ x ≤ 9. Do your plot on a separate piece of paper. Then answer the questions to check your results. A Questions: x 9 m 40 kg (a) If x= 3 m, the tension in cable AC is (b) If x = 7.3 m, the tension in cable BC is B i i N N
kindly show complete solution:
Two cables are tied together at C and are loaded as shown. Knowing that P = 316 N and R = 357 N, Determine the tension in cables AC. %3D В 30° 30° R C /45°
A cable PQ of length 25.m is supported at two ends at same level as shown in the figure. The horizontal distance between the supports is 20 m. A point load of 150 kN is applied at point R which divides it into two equal parts. 20 m Q R + 150 kN Neglecting the self-weight of the cable, the tension (in kN, in integer value) in the cable due to applied load will be