If the tension in the gantry-crane hoisting cable is T = 24 kN, determine the unit vector n in the direction of T and use n to determine the scalar components of T. Point B is located at the center of the container top. Assume a = 18 m, b = 9 m, c = 4 m, d = 10 m, e = 12 m, f = 7 m, and h = 25 m.

If the tension in the gantry-crane hoisting cable is T = 24 kN, determine the unit vector n in the direction of T and use n to determine the scalar components of T. Point B is located at the center of the container top. Assume a = 18 m, b = 9 m, c = 4 m, d = 10 m, e = 12 m, f = 7 m, and h = 25 m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two blocks are supported by a pulley along an incline as shown. The lower block B has a weight of 37 lbs and the higher block A has a weight of 22 lbs. Assume that there is friction between the blocks with fls = 0.14 and assume friction between block B and the incline is also s 0.14. Determine the angle z for which motion is impending. - 27lb I Tension in block A as a function of a can be written as TA Tension in block B as a function of a can be written as TB Thus, impending motion is at = 3716 AB degrees.
Given: A 10 m pole supports a horizontal cable CD and is supported by a ball-and-socket joint at A as shown in the figure below. Cable CD is parallel to the r-z plane (which implies that a vector from C to D has no y-component) and is oriented = 20° from the x-y plane. y D 10 m 6 m 8 m C B 6 m 6 m Required: Find the tension in cables BE and BF and the components of the reaction force at support A when the tension in cable CD is 20 kN. Hint: Find the tensions in cables BE and BF first, then find the reactions at A.
The solid 34 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. For the loading shown, determine: (a) the shaft deflection at pulley B. (b) the shaft deflection at pulley C. Assume P = 810 N, Q = 480 N, LAB = 260 mm, LBC = 400 mm
IHE BARS AB AND AC ARE JÕINED BY A PIN AT A AND A HORIZONTAL CABLE. THE VERTICAL CABLE CARRYING THE 200-kg MASS IS ATTACHED TO THE PIN AT A. DETERMINE THE TENSION IN THE HORIZONTAL CABLE. NEGLECT THE WEIGHTS OF THE BARS. 30° 60° 3 m 2 m B 200 kg
A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B, C, and D. If the tension in wire AB is 630 lb, determine the vertical force P exerted by the tower on the pin at A.
Take F = 320 N and d = 1.0 m. (Figure 1) Figure 1.5 m B C -2 m D F 1 of 1 > Part A Determine the force in cable AC needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. FAC = Submit Part B Value Request Answer Submit O ▼ Determine the force in cable AB needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. μA FAB = Value Units Request Answer wwwww Units ? ww ?
B The two blocks shown are originally at rest. Neglecting the masses of the pulleys determine the tension in the cable. Given: . • Weight of block A = 220 lbs Weight of block B = 190 lbs • kinetic friction coefficient = 0.55 Find: A • Tension in cable = lbs Your Answer:
Cable ABC supports two loads m1 = 60 lb and m2 = 144 lb as shown. Knowing that b = 21 ft, determine the required magnitude of the horizontal force P and the corresponding distance a 12 ft 9 ft A a ·b B m1 C m2 P
a water supply crossing a wide river is to be supported by a flexible wire cable with an allowable tensile of 20000kg. the pipe weight 50 kg per meter and has a total length of 60m. a. determine the minimum sag of the cable b. determine the tension the lowest point of the cable. c. if the sag is to be 2m. what is the tension at the support?
Two cables are tied together at C and are loaded as shown. Knowing that P = 363 N and R = 324 N, Determine the tension in cables AC.
The cargo box as shown weighs W = 1200 lb. The force P = 800 lb is just sufficient to lift the box off the floor. The 2-D concurrent force system of the joint O is shown as well. Using the equilibrium equations: ∑ ???= 0 ; ∑ ???= 0, 1) Determine the tension force in the cable T;2) Determine the corresponding value of β
A hollow steel crank has an outside diameter of 57 mm and an inside diameter of 52 mm. The load magnitudes are Py= 400 N and P, = 210 N, and the length dimensions are a = 125 mm, b = 344 mm, and c = 225 mm. y Py K Pz b Determine the magnitudes of the equivalent forces and the equivalent moments that act at the section that contains point K. (a) Axial force in x direction Px (N) (b) Shear force in y direction V, (N) (c) Shear force in z direction V, (N) (d) Torque around x axis Tx (N-m) (e) Bending moment around y axis M, (N-m) (f) Bending moment around z axis M, (N-m)