Take F = 320 N and d = 1.0 m. (Figure 1) Figure 1.5 m B C -2 m D F 1 of 1 > Part A Determine the force in cable AC needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. FAC = Submit Part B Value Request Answer Submit O ▼ Determine the force in cable AB needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. μA FAB = Value Units Request Answer wwwww Units ? ww ?

Take F = 320 N and d = 1.0 m. (Figure 1) Figure 1.5 m B C -2 m D F 1 of 1 > Part A Determine the force in cable AC needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. FAC = Submit Part B Value Request Answer Submit O ▼ Determine the force in cable AB needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. μA FAB = Value Units Request Answer wwwww Units ? ww ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The plate is horizontal, is in equlibrium, and weighs 1450 N. Determine the tension in cables AB, AC, and AD. Use Excel to solve the system of equations, and submit your Excel file (along with the pdf file of your solutions to these problems). 1.2m B AP 0.9m 0.9 m- C D 0.8 m 0.8 m
STRENGHT OF MATERIALS (Please write the solutions correctly and legibly. No long explanation needed. Answer in 3 decimal places. Rate will be given. 15 minutes left :<) Write the shear and moment equations for the beam loaded as shown and sketch the shear and moment diagrams. Indicate all values at the change of load points. Use a ruler for the stright line part/s of the diagrams.
Using shear and moment diagrams, determine the value of the maximum shear of the loadings shown in the figure below. Answer must be in pounds (Ib), input numeric value only. P (Ib) M (Ib-ft) RA Xft y ft z ft Rp M=4621 Ib-ft P=1587 Ib x=3 ft y=5.6 ft z=2.8 ft Round your answer to 2 decimal places. Add vour answer
Please reply as soon as posible, thanks! I don´t have much time:( Static Problem: The spool shown in the figure has a weight of WAB = 27,50 N , and its center of gravity is located at its geometric center O, the spool has a larger radius R=0,17 and an inner radius r=0,13, and it has a coiled rope. Block C has a uniform weight WC= 60 N. Consider the friction between block C and the top of the spool at A, between the spool and the surface at point B and between the rope and pulley D, the friction coefficients are respectively: μs@A=0,30, μs@B =0,45 and μs@D=0,35. The chord is parallel to the plane. Carry out: a) The free-body diagrams of the block and the reel (Please make the diagram well drawn). b) The calculation of the maximum value of P that can be applied without losing the equilibrium of the system.
A T₁ Co B S T₂ C L₂ T3 L3 T4 O The image above shows a solid shaft with various torques applied in the directions shown. The values for each torque are as follows: T₁ = 800 N•m, T₂ = 600 N.m, T3 = 400 N·m, and T4 = 200 N·m. The values for the maximum shear stress in each section are as follows: TAB = 75 MPa, TBC = 90 MPa, and TCD = 100 MPa. Find the minimum allowable shaft diameter.
A kettlebell with a mass of 10 kg is suspended by three cables as shown in the figure and parameter table. Find the tension in the 3 cables. L4 A cc 080 BY NO SA 2021 Cathy Zupke B parameter value 4 1 2 8 10 L₁ L₂ L3 L4 M The tension in cable AB is The tension in cable BC is The tension in cable BD is M C units |εεεε m m m m kg Z N N IN y
The beam supports the triangular distributed load shown below with Wmax=770 lb/ft. The reactions at A and B are vertical. 6 ft BI D 6 ft C 6 ft W B E 4.5 ft 4.5 ft
The shaft is supported by a journal bearing at A and a thrust bearing at B. (Figure 1) Figure -6 ft- 3000 lb 2500 lb 75 lb/ft I pontot, -12 ft 1 of 1 2 ft Part A Determine the normal force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Nc = Submit Part B HÅ Submit Value Part C Request Answer Determine the shear force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Vc = Value μA Units Request Answer ? Units ? Review
3. The roof truss is subjected to the loadings shown. Determine the force in each member and indicate if the members are in tension or compression. Approximate each joint as a pin. 200 N C 300 N 300 N 1.5 m B, D. 4 m 3 т H 3т G F 3 m 3 т o00 00 00 o oo 150 N Paint X ite
L13 L/2 L/2 B. A Prob. 5 (10 points) The figure shows a drill-rig pipe that is being picked up by a crane at point C. The pipe has dimensions L= 32 ft., do = 4. 50 in., and d; = 3. 60 in., and weighs 21 lbf/ft. At the moment when 0 = 30°, please calculate the principal stresses at: (a) the point marked B, and (b) at the point given by z = 0, y = do/2 at the same cross-section (i.e. at L/2 from the point A).
The man attempts to pull down the tree using the cable and small pulley arrangement shown in (Eigure 1) The tension in AB is 55 lb and y=39° Figure D 20° e <1 of 1 Part A Determine the tension in cable CAD Express your answer to three significant figures and include the appropriate units. T= Part B μÀ Submit Request Answer Value Submit Determine the angle which the cablemakes at the pulley Express your answer in degrees to three significant figures. VA2 Ivec Request Answer Units P Pearson ? ?
Determine the force in each member of the loaded truss. All triangles are equilateral with side length d. The forces are positive if in tension, negative if in compression. Answers: §§ 8 8 8 8 8 4 ė AB- AG= i BC= i i i i ¡ 1 i i i i B G 7.0 kN KN kN KN KN kN KN kN KN KN 6.2 KN kN KN kN D