6-13 A brass rod is a firm fit inside a steel tube 2 cm inside diameter and 4 cm outside diameter when the materials are at 15°C. If the rod and tube are now heated to a temperature of 150° C, calculate the maximum stresses in the brass and steel. Take the coeffi- cient of expansion for steel and brass as 10-8 × 10-6 and 18 × 10-6 per °C respectively. For steel E = 200 GPa and for brass E = 85 GPa. Poisson's ratio for both rod and the tube. %3D 1/3. Neglect longitudinal frictional forces between the

6-13 A brass rod is a firm fit inside a steel tube 2 cm inside diameter and 4 cm outside diameter when the materials are at 15°C. If the rod and tube are now heated to a temperature of 150° C, calculate the maximum stresses in the brass and steel. Take the coeffi- cient of expansion for steel and brass as 10-8 × 10-6 and 18 × 10-6 per °C respectively. For steel E = 200 GPa and for brass E = 85 GPa. Poisson's ratio for both rod and the tube. %3D 1/3. Neglect longitudinal frictional forces between the

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

SHOW ILLUSTRATION AND SOLUTION Problem 1: A steel rod with a cross - sectional area of 150 mm2 is stretched between 2 fixed supports. The tensile load at 20 oC is 5 kN. Use E = 200 GPa and  = 11.7 x 10- 6 /oC 1. At what temperature will the stress be zero?2. What will be the stress at - 20
QI A rigid bar ABCD is pinned at end A and supported by two cables of equal length at points B and C.The cable at B has nominal diameter D=12 mm and the cable at C has nominal diameter D= 20 mm. IF a load P=30 -dc KN acts at end D of the bar. What is the stresses for the cables at B and C if the temperature rises by 60°C. (E = 140 GPa and a=12 x 10/°C for both cables). -26 to -26- P
The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 80 mm and its thickness is 25 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket.just bearing stress in the rectangular bar. Rectangular bar Support bracket
A circular bar of length 400 mm and tapering uniformly from 50 mm to 25 mm diameter is held between rigid supports at the ends. Calculate the maximum and minimum stress developed in the bar when the temperature is raised by 30°C. Take E = 2 × 105 N/mm² and a = 1.2 x 10-5. per °c
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. The diameter of aluminum rod (1) is 2.50 in., the diameter of brass rod (2) is 1.75 in., and the diameter of steel rod (3) is 3.00 in. Determine the axial normal stress in each of the three rods. Assume P = 5 kips, Q = 3 kips, R = 13 kips and 5 = 24 kips. The normal stress is positive if tensile and negative if compressive. σ₁ = Answers: 0₂ = (1) 03 = (2) i i A Q B C D ksi ksi ksi
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.24 mm the values of elastic modulus for steel is 221 MPa. Take H1 = 4 cm, H2 is 2 x 2 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. = 9 cm, top bar (R) IP Solution: R cm x RCm Steel bar i) Magnitude Force, P = H1 cm ii) Stress-induced in the top bar = Q cm x Q cm Steel bar H2 cm iii) Stress-induced in the bottom bar =
A pushrod in the valve mechanism of an automotive engine has a nominal length of 203 mm. If the rod is made of SAE 4140 steel, compute the elongation due to a temperature change from -20°C to 140°C. TABLE 3-4 Coefficients of thermal expansion, a, for some t nd concrrete
A steel rod bolt 8mm diameter inside fits loosely on an aluminium tube and 16mm outside diameter. A nut is fitted into the bolt and tighten against the tube, until the stress in the bolt is 40N/mm². Calculate the stress in the tube. If the temperature of the assembly is now increased by 100°C. What will be the new stress in each component?
An aluminum tube of outer diameter R2 = 50 mm is heated such that it is mounted over a steel shaft of radius, R = 20 mm as shown in the figure The length I of the member is 3 m. MT R Ri If a G, = 77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, Determine the maximum shear stress in shaft 1. 777
Q3: A rigid beam ABCD is supported as shown. Initially and at room temperature the beam is horizontal and carries no load. Calculate the force in the rods when the temperature of aluminum rod only is raised by 120°C. Steel Wire A- 50 mm E-200 Gpa L-2 m Brass Rod 2. A-300 mm E-83 Gpa L-2 m a = 12um/m C Aluminum Rod Gap 2mm a- 19um/m C A=400 mm E= 70 Gpa L=3 m 23um/m C timt 1m Im
The rigid bar of negligible weight is supported as shown in the figure. If W 80 kN, compute the 2 temperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data: A (in-) a PF) E (GPa) Steel Rod 300 11.7 x 10 200 Bronze Rod 1400 18 х 104 83 Bronze 3 m Steel 1.5 m →| 1.0 m- 2.5 m +1.5 m W
Brass Problem 3: A composite bar is made by attaching a copper rod of length 900 mm and diameter 30 mm and a brass rod of length 600 mm and diameter 45 mm as shown. A load of 20 kN is applied at 20°C. For unyielding supports, find the stresses in the materials when the temperature rises to 50°C. For copper, E = 120 GPa and a = 18 x 10-6 °C. For brass, E = 90 GPa and a = 20 x 106 °C. Copper 20 kN 900 mm 600 mm