Draw the shear and moment diagrams for the following beams 50KN-m60 KN/m1m1m3m2m40KN/m100KN-m9.2m1 m2 m8.

Only one question is allowed to solve.

Answered: 50KN-m 60 KN/m 1m 1m 3m 2m 8.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Homework For the following loading diagrams, find the shear and moment diagrams and calculate the maximum moment. SA 3 7
3. Draw the shear and moment diagrams for the beam. 6kips/ft 17 kips 9ft 5 ft A B C
Construct the load, shear, and moment diagrams for the following beam conditions using the semigraphical approach A 5' 51
Draw the shear and moment diagrams for the loaded cantilever beam where the end couple M1 is adjusted so as to produce zero moment at the fixed end of the beam. Then answer the questions: a. at x = 1 ft, V = ? and M=? b. at x = 6.9 ft, V=? and M=? c. What is the maximum (absolute value) shear? d. What is the maximum (absolute value) moment? 440 lb/ft 5.1' 5.1' M₁
Write the shear and moment equations for the beam loaded as shown below. A 50 Kn/m 2.0 m THE B 2.0 m C 20 Kn/m 2.0 m D
Write shear and moment equations for the beams in the following problems. In each problem, let x be the distance measured from left end of the beam. Also, draw shear and moment diagrams, specifying values at all change of loading positions and at points of zero shear. Neglect the mass of the beam in each problem.
Homogeneous beams AB and CD weigh 600 lbf and 500 lb respectively. Draw the shear force and bending moment diagrams for beam CD. What is the maximum value of the shear and moment.
Find the equations for load forces, shear forces, and bending moment diagrams. Draw the shear and moment diagram.
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=12.0 ft, b=6.5 ft, c= 7.0 ft, w = 7 kips/ft and M = 230 kip-ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Determine the shear force acting at each of the following locations:(a) x = 0+ ft (i.e., just to the right of support A)(b) x = 12.0 ft (i,e., at point B)(c) x = 18.5- ft (i.e., just to the left of the support C)(d) x = 18.5+ ft (i.e., just to the right of the support (C)(e) x = 24.5 ftNote that x = 0 at support A. Determine the bending…
Draw the shear and moment diagrams for the beam using graphic method. 2 kip/ft 30 kip-ft 5 ft -5 ft 5 ft
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. Let a=4.00 m, b=5.25 m, c= 2.50 m, P = 26kN and M = 160kN-m. Construct the shear-force and bending-moment diagrams. Use the bending-moment diagram to determine the maximum positive bending moment, Mmax, pos, and the maximum negative bending moment, Mmax, neg.
2. Draw the shear and moment diagrams for the beam where A is roller and B is pin support (refer to Figure 2). 150 kip. ft A 50 ft 2 kip/ft 100 ft 150 kip. ft 50 ft

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS