50 kip 10 kip-ft

Q: Specifications of the steel rod at B. Length=2 meters diameter= 25 mm E= 200 GPa Show complete…

A:

Q: The internal loadings at a cross section through the shaft consist of an axial force of 1500 kN, a…

A: Given: axial force, P =1500KN Bending moment, M =40KNm Torsional moment, T =40KNm radius of shaft,r…

Q: с 1 ft 2 ft B 150 lb-ft/ft A 2 ft A copper pipe is tightly secured to the wall at C and a uniformly…

A:

Q: a) the principal stress and planes and (b) the maximum in-plane shear stress, average stress and its…

A:

Q: Determine the normal and shear stresses at point B. 5-10 min 180 mm 180 mm 60 mm - 30 KN

A: Given data dimension of cross section = 180mm× 60 mm find the normal and shear stress at point B.

Q: Q1/ The copper pipe has an outer diameter of 3.0 in. and an inner diameter of 2.8 in. If it is…

A:

Q: Determine the principal stresses and the absolute maximum shear stress.

A:

Q: The cylindrical tank with a spherical endcap has an outer radius of 2 m and a wall thickness of 25…

A:

Q: The two rods support the vertical force of P = 40 kN. Determine the normal stress in rod AB and AC…

A:

Q: Air pressure in the cylinder is increased by exerting forces P = 3 kN on the two pistons, each…

A: Force, P = 3 kN = 3000 N Radius, r = 45 mm = 0.045 m Wall Thickness, t = 2 mm = 0.002 m

Q: Q2: If the block is subjected to the centrally applied force of 600 kN, determine the average normal…

A: Given: the block is subjected to applied force =600 kN we have to find the average normal stress in…

Q: 30 mm and 40 mm, respectively. Determine the principal stresses and

A:

Q: 1. The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A…

A: To find: The longitudinal and hoop stress developed in the wall of the pipe, also draw the stress on…

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A: Given data: The normal stress in x-direction is: σx = -15 ksi (compressive stress is taken as…

Q: Determine the maximum shear stress If maximum principal stress=50 MPa, Minimum principal Stress=20…

A:

Q: Determine the normal stress in a ball, which has an outside diameter of 185 mm and a wall thickness…

A: Outside ball diameter, do=185 mmThe wall thickness of the ball, t=3.1 mmA gage pressure inside the…

Q: Two fully loaded tractor trailers travel over the bridge putting substantial loading on the…

A: The objective of this question is to calculate the shear strain at point T when a vertical…

Q: The steel tube below has an inside diameter of 2.75”, and an outside diameter of 3”. If the tube is…

A: The polar moment of inertia of the bar can be determined as,

Q: The assembly consists of a solid 15 mm diameter rod connected to the inside of a tube using a rigid…

A:

Q: 13/ 12 a 1 m 2 m a

A:

Q: 9-74 If the box wrench is subjected to the 50 lb force, determine the principal stresses and maximum…

A:

Q: The gear motor can develop 1 10 hp when it turns at 300 rev>min. If the shaft has a diameter of 1…

A: Given: The power developed by the gear motor is P=1/10 hp. The angular velocity of the gear motor is…

Q: The grains of wood in the board make an angle of 20 with the horizontal as shown. Using Mohr's…

A:

Q: The copper pipe has an outer diameter of 50 mm and an inner diameter of 40 mm. It is tightly secured…

A:

Q: The spherical pressure vessel has an inner diameter of 2 m and a thickness of 10 mm. A strain gage…

A: Given Data: Inner diameter of sphere is di = 2 m. Thickness of sphere is t= 10 mm. Length of strain…

Q: The solid bar has a diameter of 50 mm. The two forces and the x-y-z coordinate system which is…

A:

Q: The resultant stress at a point 0 in a structural component has a value of 10 ksi and makes angles…

A: Use the equations for stress transformation, to  determine the normal (σσn) and shear (τ) stresses…

Q: The long bolt passes through the 20-mm-thick plate. If the force in the bolt shank is 9 kN,…

A: Given data: ● The force applied on the bolt shank: F = 9 kN = 9000 N ● The thickness of the plate…

Q: The 2-m-long tube is made of an elastic perfectly plastic material as shown. Determine the applied…

A:

Q: The following shaft consists of a tube AB and a solid rod BC. The tube has an inner diameter of 25…

A: Please check sign convention I took compressive as negative.If you have any doubts please comment

Q: 5. Two forces act on the solid circular rod (r=.005 m) as shown. Using Mohr's circle, determine the…

A: Draw mohr circle and find principal stresses and maximum shear stress.

Q: The wide-flange beam is subjected to the 50-kN force. Determine the principal stresses in the beam…

A:

Q: The clamp presses the smooth surface at E when tightening the screw. If the tension in the bolt is…

A: Given data as per question Tension in the bolt =40 kN   Support reaction are shwn on FBD (a)Internal…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.