5.1. If a pancake is in. thick (average for fluffy pancakes) and has the same ratio for thicknes= to diameter as the atmosphere, what would its diameter be? If a pancake has a diameter o 6 in. (a typical value) and has the same thickness-to-diameter ratio as the atmosphere, wha would its thickness be?

5.1. If a pancake is in. thick (average for fluffy pancakes) and has the same ratio for thicknes= to diameter as the atmosphere, what would its diameter be? If a pancake has a diameter o 6 in. (a typical value) and has the same thickness-to-diameter ratio as the atmosphere, wha would its thickness be?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1-61.M Figure P1-61 shows the shape of a slug to be punched from a sheet of aluminum 5.0 mm thick. Compute the shear stress in the aluminum if a punching force of 38.6 kN is applied. 43 mm 35 mm -8 mm
8. A solid steel shaft 5 m long is stressed to 60 MPa when twisted through 4". Find the shaft diameter in inches.
Each nail can support a shear force of 750 lb. The allowable shear stress for the wood is Tallow = 500 psi. (Figure 1) Figure 2 in. 12 in. 12 in. 2 in. Part A Determine the maximum shear force V that the beam can support. Express your answer in kilopounds to three significant figures. IVE ΑΣΦΑΛΙ V = Part B vec Determine the corresponding maximum nail spacing s. Express your answer in inches to three significant figures. S = VE ΑΣΦ ↓↑ vec ? ? kip in.
Please simply sketch the shear stress diagram 0.5 in. 0.6 in. 0.8 in. 0.2 in. 0.6 in. B -6 ksi 36 ksi --
A steel punch having diameter 10 mm is used to make hole in a 2.5cm thick steel plate. What will be the compressive stress if the maximum shear stress is 20 k N/m?
Show complete solution pls A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length of the pipe is L = 6.0 m. Thechanges in dimension caused by an increase in temperature of 80°C for the:1. Outside diameter 2. Inside diameter 3. LengthNote: All answer must be round off up to 3 decimal places.
QUESTION 4) For the given plane state stress, if the components at the inclined surface is known and the normal stress is known to be zero about the +ty direction, calculate the stresses that will occur in the 14 MPa MPa plane where the direction of the normal axis is x, and show all an oriented element. 30
B=55⁰ inside diameter = 28.6in. wall thickness=0.35 in. allowable normal stress perpendicular to the weld = 18 ksi allowable shear stress parallel to the weld =8 ksi What is the largest gage pressure inside the tank? Answer in psi rounded-off to 3 decimal places K
Determine the state of stress of a beam at the point shown in Figure 2 to represent: a) the principal stresses; b) the maximum in-plane shear stress and the associated average normal stress. c) For each of the two cases mentioned in (a) and (b), determine the corresponding orientation of the element with respect to the original element shown and sketch the results relative to the longitudinal axis of the beam. Please show the full working to provide sufficient information for the sketching to be complete. 15MPa Figure 2 20° 50MPa
I need answer please in 10 min with my best wishes
60 min 24 mm Q1// Determine the principles strain for the point (A) of the bar which 32 nmm that is under three forces as shown in 180 mm 40 mm 750 N 16 mm 30 mm 500 N the figure. 1 kN
use abaqus to solve this