5.01f the built-up beam is subjected to an internal moment of M 75 kNm, determine the amount of this internal moment resisted by plate A. 150 mm 20 mm 150 mm 150 mm 10 mm M 10 mm 300 mm

Q: For the truss shown, loads are transmitted to the bottom chord. Draw the influence diagram of member…

A: Maximum tensile force The maximum tensile load a body can sustain before failure divided by its…

Q: F2-10. Determine the components of reaction at the fixed support D and the pins A, R and C of the…

A: Consider the free body diagram of beam BC. Consider the equilibrium moment about point C. Consider…

Q: Problem 4-145 4-145. Replace the loading by an equivalent resultant force and couple moment acting…

A: Given,  A structure, FBd:-

Q: 2. [Ac, 0c] Use conjugate beam method. (EI is constant) 30 ft B 15 ft 15 k C

A:

Q: m- A-36 steel rod is subje shown. Determine the displacement of end A with 30 kN 30 A 400 mm B 4 5…

A:

Q: DY *5-72. Determine the components of reaction at the ball- and-socket joint A and the tension in…

A:

Q: equivalent resultant force and couple moment at point A. +103. Replace the loading system acting on…

A: to find resultant

Q: Q2. Draw the influence line for (Rb, Re, Rf, Rg. Mp, Mm, and Mb) P A B C D mm n b E F mm b

A: Step 1: Step 2: Step 3: Step 4:

Q: التاريخ: - for fig, find reactions at supports A and c Rollar 8m 10 kN/m hing B 8m 6 V₁₂ 10 c fix…

A:

Q: A propped beam is simply supported at A and foxed at B. It carries a uniform load of 400 KN/m. Point…

A: Step 1:Step 2:Step 3: Step 4:

Q: Problem 2) For the truss shown, solve for the influence line for member CH. The trucks run across…

A:

Q: 1.80 1.80 1.80 3 kN A B -1.80- с D -1.50-1 K -1.80- F P3= 16 KN. G P1 H P2 P3

A: Determine support reactions: HH=10+13+16=39 kN Take Moment @ A, (10×5.4)+(13×3.6)+(16×1.8)=(VH×5.1)…

Q: Compute the reactive forces of the pin at A and the roller at B.

A: To determine the support reactions.   The given truss can be solved for the reactive forces by…

Q: Prob 4. The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of…

A: Young's modulus of A-36 steel = 29007.5 ksiA point load of 10 Kip is applied at E.To determine the…

Q: Handle forces F₁-(41-45-10k) N and F,- (21 are applied to the electric drill(Eigure 1) Replace this…

A:

Q: Problem 2: Replace the three forces which act on the bent bar by a force-couple system at the…

A: In this problem, we are given three forces acting on a bent bar. We must replace these forces with a…

Q: The two forces are applied to the end of the boom OA. Determine the force F so that the resultant of…

A: Given:- The two forces are applied to the end of the boom OA The magnitude of one force = 200 lb The…

Q: P (kN) Şekildeki kafes sistemde çubuk kuvvetlerini Basınç-çekme hesaplayınız. durumlarını A B…

A:

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.