5. In preliminary design studies for a sun- powered car, it is estimated that the mass of the car and driver will be m kg and the torque produced by the engine will result in a F; newton tangential force on the car. Suppose that the car starts from rest on the track at A and is subjected to a constant F; newton tangential force. Determine the magnitude of the car's velocity and the normal component of Rm END B A START 102.743 kg force on the car when it reaches B. m = 121.239 newton Ft l = 303 ..m 75.75m R

5. In preliminary design studies for a sun- powered car, it is estimated that the mass of the car and driver will be m kg and the torque produced by the engine will result in a F; newton tangential force on the car. Suppose that the car starts from rest on the track at A and is subjected to a constant F; newton tangential force. Determine the magnitude of the car's velocity and the normal component of Rm END B A START 102.743 kg force on the car when it reaches B. m = 121.239 newton Ft l = 303 ..m 75.75m R

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

n engineer is designing a spring to be placed at the bottom of an elevator shaft. If the elevator cable breaks when the elevator is at a height H above the top of the spring, calculate the value that the spring constant k should have so that passengers undergo an acceleration of no more than 9.0g when brought to rest. Let N be the total mass of the elevator and passengers. Spring constant k that the spring should have so that passengers undergo an acceleration of no more that 9.0g
In the figure, masses of a sphere of radius r and mass m are compressed between two neglected rods. The length of the bars is indicated by l, and the angle they make with the vertical by the angle. The force applied from the ends of the rods is in the horizontal direction and its magnitude is given by P. Friction between sphere and rods is neglected. Therefore, find the acceleration of the sphere in the vertical direction when the angle is 30º in terms of the given magnitudes. Note: Treat the sphere as the material point.
Part A The 2.2-Mg car increases its speed uniformly from rest to 17 m/s in 40 s up the inclined road. Determine the maximum power that must be supplied by the engine, which operates with an efficiency of e = 0.8. (Figure 1) Express your answer with the appropriate units. HA Pmax = 52.39 kW Submit Previous Answers Request Answer X Incorrect; Try Again Part B Also, find the average power supplied by the engine. Figure 1 of 1 Express your answer with the appropriate units. Pavg = |26.19 kW Submit Previous Answers Request Answer 10 X Incorrect; Try Again
OR Fig. 3 A robotic arm shown in Fig. 3 is programmed so that the 0.4-kg part A traces the radial path defined by r = 1–- 0.5 cos (2nt) meter and tranverse path of 0 = 0.5 – 0.2 sin (2nt) rad respectively. a) Calculate the velocity magnitude of part A at 1= 3 seconds. b) Determine the radial and transverse components of the force exerted on A by the robot jaws at 1= 2 seconds. Show the necessary Free-Body and Kinetic diagram to support your analysis.
Question 3 The speed of the engine mechanism shown in Figure 1 is controlled by the Porter governor. All arms of the governor are 20 mm and are hinged at a distance of 4 mm from the axis of rotation. The mass of each ball is 100 g and the mass of the sleeve is 500 g. The governor sleeve begins to rise at 40 rad/s. when the links are at an angle of 5° to the vertical. Assuming the friction force to be constant 3.1. Draw the port governor mechanism and clearly lable it. 3.2. Calculate the minimum speed of rotation (in rad/s) when the inclination of the arms to the vertical is 10°.
Motorized moving platform is lifting a car with some acceleration. If the combined weight of the lift platform and car is 2800kg, and the motorized lift weight is 200000kg, determine the maximum acceleration of the platform before tipping occurs. Weight of the platform a=2.1m, b = 4m, c = 4.2m, d = 3m FBD of the lift: Vertical lift platform. center of gravity (car) FBD of the car: a C Too center of gravity (lift)
The rotor of a gas turbine is rotating of 12 rad/s when the turbine is shut down. It is observed that 4 min is required for the rotor to coast to rest. Assuming uniformly accelerated motion, determine the number of revolutions that the rotor executes before coming to rest
A string is wound around a pulley of diameter of 0.2 m. One of its ends is tied to the pulley and the other end to a weight hanging freely. The weight falls a distance of 4 m from the rest in 3 s. Determine the total distance through which the weight should fall so that the velocity of the pulley will be 400 rpm. OPTIONS: 1.Around 10 m 2.Around 15 m 3.Around 12 m 4.Around 6 m 5.Around 8 m 6.None
The torsional spring has a stiffness of 20 N-m/rad and is undeflected when the 3-kg uniform slender bar is in an upright position. If the bar is released from rest in the horizontal position shown, find its angular velocity as it passes the vertical position. Neglect friction effects. 4 Type here to search ThinkVision K - Pan Tab Cape Look Esc Q A Z G FT W S # ONDA 3 F2 E D A $ 4 R F 5 F4 T G XCVB 8 a Y H N P6 F6 U J M F7 K ( F8 F10 F11 +Backspace Enter T F12 Shift Print Screen SysRq Insert 0.5 m Scroll Lock Delete Home Break End Page Up Page Down Naam Lock K 37°F Cloudy Home Lenovo B 20
23-A truck of mass 5 tonnes was moving with a velocity of 110 km/hr. The brakes were applied to bring the truck to 25 km/hr in 7.5 seconds . Determine the uniform force exerted by the brakes. Also find the velocity it will reach if the same force is applied in the same direction for 750 m and also find the time taken. The uniform force exerted by the brakes in N is The velocity it will reach if the same force is applied in the same direction for 750 m in m/s is The time taken if the same force is applied in the same direction in seconds is
1. Parcels are moved via conveyor with velocity vo down to a colinear incline that is static at point A where sliding begins. The parcels eventually fall off at point B, which is 7.0 m past A. If the coefficient of kinetic friction on the incline is 0.40, find the velocity of the conveyor belt, vo, such that the parcels have zero velocity at point B. 7m 15°
A brake test for an automobile is conducted. During the brake test, the automobile of mass 1800 kg (including driver) is travelling at the speed of 110 km/hr as it passes point A, and the car descends a hill of 1in 2 (Sine). The driver applies brakes so as to bring the car speed at B to 50 km/hr. The total frictional resistance to motion is 235 N. Using Work-Energy Method, Calculate the following required to bring the car to 50 km/hr from 110 km/hr in 210 m (From Point A to Point B) B Determine the Value of Total Energy about Point A TE= Determine the Value of Total Energy about Point B TEb= Determine the Value of Breaking Force needed Fb= N A