A truck of mass 5 tonnes was moving with a velocity of 110 km/hr. The brakes were applied to bring the truck to 25 km/hr in 7.5 seconds . Determine the uniform force exerted by the brakes. Also find the velocity it will reach if the same force is applied in the same direction for 750 m  and also find the time taken.       The uniform force exerted by the brakes in N is The velocity it will reach if the same force is applied in the same direction for 750 m in m/s is The time taken if the same force is applied in the same direction in seconds is

Q: A truck of mass 10 tonnes was moving with a velocity of 130 km/hr. The brakes were applied to bring…

A:

Q: Q2 The constant tensions of 200 N and 160 N are ap- plied to the hoisting cable as shown. If the…

A:

Q: A truck of mass 6 tonnes was moving with a velocity of 145 km/hr. The brakes were applied to bring…

A:

Q: A car weighing 500 kg moving with a speed of 10 m/s takes a turn around a circle with a radius of 25…

A:

Q: When the m kg box is moving upward with an acceleration (a) given that: m = 600 kg a = 6 m/sec Then…

A: Given values are - m =600kg , a =6m/s2 The equation for force balance will be-T -mg =maT=…

Q: A car starts from rest and accelerates uniformly to a speed of 72 km/hr over a distance of 500 m.…

A: Given Data  Initial Velocity, u=0 m/s Final velocity, V=72 kmph=20 m/s S=500 m…

Q: 5. A slider of mass 10 kg moves along a slipway as shown. The spring has a value of K = 60 N/m and…

A: The given information in the problem is shown in the following attached image:

Q: A truck of mass 3 tonnes was moving with a velocity of 140 km/hr. The brakes were applied to bring…

A: Given data: -  The mass of the truck is m = 3 tonnes. The velocity of the truck is u = 140 km/hr.…

Q: ė 6 = 4 rad/s, 6 = 3 rad/s² 0 = 180°

A: Introduction:- The rate of change of a body's momentum must match the net force acting on the body…

Q: 2- Each ball has a negligible size and a mass of 5 kg and is attached to the end of a rod whose mass…

A:

Q: The 2-1b spool slides along the smooth horizontal spiral rod, r= (20) ft, where is in radians, as…

A:

Q: Bodies A and B shown in the figure are connected to each other by two ropes. Body b is located on…

A: The behaviour of body in motion without external force is studied under kinematics. The behaviour of…

Q: The helical path is wound around the circular cylinder with radius R . The step h= 2*pi*R. The…

A:

Q: The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined…

A: 1. Find the velocity of the block after it moves 20m starting from rest. 2. If the 100-N pull is…

Q: Use 3 decimal places The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by…

A:

Q: An SUV hauling a trailer is travelling at 25 m/s when the driver hits the brakes. The 1.4 MT trailer…

A: Given data Speed of SUV and trailer = 25 m/s Mass of trailer = 1.4 MT = 1.4 x 1000 kg Mass of SUV =…

Q: Q2: The speed of a car increases uniformly with time from (70 km/h) at A to (120 km/h) at B during…

A:

Q: Calculate the acceleration and the time taken to er acceleration raises the speed to 90 km/h in 10…

A: Given: u=0 v=72 kmph=20 m/s s=500 m v2=90 kmph t2=10 s t3=5 s To determine: The acceleration The…

Q: 1- The roller coaster car has a brake and return system that has characteristics of a spring with a…

A:

Q: 500 N 500 N VFO V=0 9 600 N H=0.20 S. 3.0 m z-

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: A train started moving from rest with a constant acceleration, and at one time it was traveling at a…

A: Given: Initial velocity, u = 30 m/s Final velocity, v = 50 m/s Distance, s = 160 m

Q: B/ Calculate the impulse of the for (a) 150N 30

A: Impulse is the product of force and time. It signifies the total amount of force required for a…

Q: 6. Masses A (2.00 kg) and B (3.00 kg) are connected to each other with string over two pulleys as…

A:

Q: If M = 2m, find the linear acceleration of the suspended body (in g).

A:

Q: 2- The swinging motion of the upper arm may be described as the follows; 0= 10 sin 0.06 t where 0 is…

A: Write the expression of angular position. θ=10sin0.06t

Q: A 8 ft- -2 ft A beam that weighs 300 lbs is supported by a roller and pin B and A respectively while…

A:

Q: A mass that weighs 8 lb stretches a spring 24 inches. The system is acted on by an external force of…

A:

Q: n engineer is designing a spring to be placed at the bottom of an elevator shaft. If the elevator…

A: Let the combined mass of elevator and passenger be M.The maximum acceleration attained is given to…

Q: The block of weight 131 lb is pushed with a force of P = 46 lb on top of two cylindrical rollers…

A:

Q: A body weighing 2,225N is being dragged along a rough horizontal plane by a pull of 445N directed at…

A:

Q: 2. A cord passing over a pulley has a 70kg mass tied on one end a 9.0kg mass on the other end.…

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.