5. For the below system, find the following: a). What is the system type? b). What is the appropriate static error constant? c). What is the input waveform to yield a constant error? d). What is the steady-state error for the a unit input in part c)? e). Validate your answer for part d). R(s) 10(s + 10) C(s) s(s + 2) (s + 1)

5. For the below system, find the following: a). What is the system type? b). What is the appropriate static error constant? c). What is the input waveform to yield a constant error? d). What is the steady-state error for the a unit input in part c)? e). Validate your answer for part d). R(s) 10(s + 10) C(s) s(s + 2) (s + 1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

can please help me understand how someone could possibly do 75 windmills in a minute?? with madeup calculations please??
Choose forming and generating operation 2 points Work Work Thre dsad dsa Generated surface Work Work O dasd dsaa
Solve it fast
Question 4 a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each piston is 175.00 mm. Calculate the cubic capacity of the engine in cm? and calculate the clearance volume per cylinder for a compression ratio, r, of 6.25. b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32 mm and the stroke of each piston is 125 mm. During testing., the engine runs at 1450 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 2.90 cm and a diagram length of 0.85 cm. The pressure scale on the indicator diagram is set to 165 kN/m per cm. Calculate the mean effective pressure (m.e.p) and the indicated power in kilowatts (kW) developed by this six-cylinder four-stroke engine. Give your answer to 2 decimal c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod…
Solve correctly
If drawn on an x-y plane what would it look like?
2) A washer is going to be manufactured by cutting operation out of 2024ST aluminum alloy sheet that has a thickness of 2.5 mm. The outside diameter of the washer is 25.0 mm, and the inside diameter is 12.0 mm. Make a rough sketch, define the geometries to be used and determine a. The punch and die size for the blanking operation b. The punch and die size for the punching operation c. The force required performing the blanking and punching operation simultaneously. The aluminum has a tensile strength = 300 MPa.
2. A rectangular plate 4X8 in. is in full contact with the base of a fixture. The hole in the workpiece has been machined to 1.500 in. at the exact center of the plate. Figure 2 shows this plate. The plug diameter is 1.495. Calculate: a) the maximum height of the plug if the 4-in. side is lifted of the plug, and b) the maximum height of the plug if the 8-in. side is lifted off the plug. c) Compare the two plug designs. Pivot Side x Sde Y Pivot d) Calculate the maximum diameter of the plug for the 8-in. lift which will permit the use of a 0.250-in height plug. e) Compare the clearance in part (d) with part (b). f) If a chamfer height of 0.1 inch is added counter sunk in the hole, what will be the plug height for cases a and b. Figure 2
5.G. 3 If a liguid has a 56 of 17 (a) What is the devrsty in Slayf fit ? Slug specific weight in Lbf? (b) What is the specific weight
If a drawing has 6 fillets with radius (1/2 inch) for imperial units drawing, name one way that you can dimension them? Remember the rule for imperial units for leading 0 for anything that is less than 1. Radius shall be in decimal.
In one sentence, explain the difference between straightness and flatness.