5. Consider a steam turbine in which the steam enters at 23.26 MPa and 808 K with a flow rate of 17.78 kg/s. The steam exits at a pressure of 5.249 kPa with a quality of 0.9566. Determine the power produced by the turbine and the isentropic efficiency. Plot the process on T-s coordinates. Show the steam dome. m= 17.78 kg/s P,=23.26 MP T=808 K w̟=? en=? P2=5249 kP 2=0.9566

5. Consider a steam turbine in which the steam enters at 23.26 MPa and 808 K with a flow rate of 17.78 kg/s. The steam exits at a pressure of 5.249 kPa with a quality of 0.9566. Determine the power produced by the turbine and the isentropic efficiency. Plot the process on T-s coordinates. Show the steam dome. m= 17.78 kg/s P,=23.26 MP T=808 K w̟=? en=? P2=5249 kP 2=0.9566

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An ideal gas expands in an adiabatic turbine from 1200 K and 900 kPa to 800 K. Determine the turbine inlet volume flow rate of the gas, in m3/s, required to produce turbine work output at the rate of 650 kW. The average values of the specific heats for this gas over the temperature range and the gas constant are cp = 1.13 kJ/kg·K, cv = 0.83 kJ/kg·K, and R = 0.30 kJ/kg·K.
5-62 Refrigerant-134a is throttled from the saturated liquid state at 700 kPa to a pressure of 160 kPa. Determine the tem- perature drop during this process and the final specific vol- ume of the refrigerant. Answers: 42.3°C, 0.0345 m³/kg P₁ = 700 kPa sat. liquid R-134a P₂ = 160 kPa FIGURE P5-62
The valve connected to a 450-liter insulated tank of air at 250 kPa and 50̊C is opened,allowing the gas to escape until its pressure drops to 120 kPa. An electric heater insidethe tank maintains the temperature at 50̊C. Using variable specific heats, Determine thefollowing:a) The mass of air withdrawn (kg)b) The energy input to the resistor (kJ)
Question 6 Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 10 MPa, 450°C, and 80 m/s, and the exit conditions are 10 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 12 kg/s. Determine (a) the change in kinetic energy (b) the power output, (c) the turbine inlet area. Answers: (a)-1.95 kJ/kg, (b) 10.2 MW, (c) 0.00447 m² P-10 MPa 7₁-450°C V₁ = 80 m/s STEAM m = 12 kg/s P₂ = 10 kPa 4,-0.92 V₂ = 50 m/s out
Air is compressed in a cylinder polytropically from an initial temperature and pressureof 84°F and 16 psia to a final of 290°F and 78 psia. The cylinder contains 0.015 lb of air,and has a piston area of 0.18 sq ft. Sketch the process on P - v and T – s coordinates andfind the work done, ft.lbfA. (-)648.41 (on) B. (-)850.85 (on) C. (-)950.85 (on) D. (+)648.41 (by)
A steam turbine receives steam at a rate of 90 MTPH at 2 MPa and 5000C and exhausts it at 0.10 MPa. Considering indicated turbine, generator and mechanical efficiencies of 95%, 93% and 90%, respectively, determine the turbine’s rated electrical power output. in MW
The figure shows the thermodynamic properties of an adiabatic steam turbine at the inlet and outlet. The mass flow of the fluid passing through it is 40 kg / s. Developed by the turbine Calculate the power.
Determine the change in entropy (BTU/R) in an isothermal process having an initial volume of 18 cu ft and a final volume of 46 cu ft. The mass is 58 lb and the specific heat is 0.24 BTU/b-R
An adiabatic capillary tube is used in some refrigeration systems to drop the pressure of the refrigerant from the condenser level to the evaporator level. The R-134a enters the capillary tube as a saturated liquid at 50°C and leaves at -22.00°C. Determine the quality of the refrigerant at the inlet of the evaporator. Use data from the tables. (Round the final answer to three decimal places.) The quality of the refrigerant is
Consider a compressor which is used to compress steam (water) through an isentropic process. At the inlet the temperature is 600°C and pressure is 3 MPa. At the exit pressure is raised to 6 MPa. What is the temperature of the steam at the exit of the compressor? (You need to do interpolation to find the exact value) Assumptions. The compressor operates steadily.
An adiabatic steam turbine receives steam from two boilers. One flow has a mass flow rate (rim) of 5.7 kg/s at 3 MPa and 600 °C. The other flow has a mass flow rate (m) of 6.0 kg/s at 0.5 MPa and 600 °C. The exit flow is at 10 kPa with a quality of 100%. Neglect ΔΚΕ (Higure 1) Part A Determine the total power output. Express your answer to three significant figures. Vα ΑΣΦ vec ? MW Submit Request Answer Part B Provide Feedback Figure West
A variable-load piston-cylinder device contains air (cp = 1.005 kJ/kgK; cv = 0.718 kJ/kgK) at 500 kPa and T=12 oC. A paddle wheelequipped within the system and turned by an external electric motor until 65 kJ/kg of work has been transferred to the air. During this process the gas volume is quadrupled while maintaining the temperature constant by transferring heat to the gas. Determine (a) the final pressure, (b) the amount of required heattransfer (c) Show this process on a P-v diagram. Do not use Table A-17 while solving this problem. YOUR ANSWER SHEET SHOULD INCLUDE THE SOLUTION AND THE TABLE BELOW (a) Pinal [kPa] = (b) q [kJ/kg]