5. A steel bar has dimension of 5 cm x 2.5 cm x 1.5 mm respectively. It is subjected 3 mutually perpendicular loads of 250 kN (Tensile), 2.5 MN (tensile), 3.5 MN (compressive) acting along length, breadth & thickness directions respectively. Find the change in volume. Take E as 200GPA & Poisson's ratio 0.25. Also find the change in Length, breadth & thickness.

5. A steel bar has dimension of 5 cm x 2.5 cm x 1.5 mm respectively. It is subjected 3 mutually perpendicular loads of 250 kN (Tensile), 2.5 MN (tensile), 3.5 MN (compressive) acting along length, breadth & thickness directions respectively. Find the change in volume. Take E as 200GPA & Poisson's ratio 0.25. Also find the change in Length, breadth & thickness.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
The cross sections of two hollow bars made of the same material are concentric circles as shown in the figure. It is given that r3 > rland r4 > r2, and that the areas of the cross-sections are the same. J1 and J2 are the torsional rigidities of the bars on the left and right, respectively. The ratio J2/J1 is r3 r2
2) Tensile strength P is applied to the rectangular cross-section, whose cross-section dimensions are given in figure A (- 5; 15). force and a pressure force of 2P acts from the point B(- 15; – 10). According to this; a) Find the load P that the section can carry b) Plot the stress distribution on the section for the load P you found c) Determine the core region of the section (6,em = 6 kN/cm² ; ơb,em = 12 kN/cm²) 40 cm B(- 15; - 10) X+ 60 cm Al- 5;15)
3. The bar shown below is composed of two pieces, AC and CD. The bar is attached to the wall at point A. The length L = 10 in. The cross sectional areas are: AAC = 4 in? and AcD = 2 in?. The Young's Moduli are: EAC =20 Msi and Ecd= 15 Msi Two forces are applied at points B and D: PB = 50 kips and PD = 20 kips. Determine: (a) the reaction force at A (specify –→ or +) and (b) the deflection of point D (specify → or +). (Hint for (b): Think about how many pieces you must subdivide the rod into.) Ans: RA = 30 kips (+), dp = 7.9167×10-3 in (E) A В C D Pp L 2L L
A metallic bar has length, breadth & thickness of 2.5 cm x 1 .0 cm x 5 mm respectively. It is subjected 3 mutually perpendicular loads of 400 kN (Tensile), 2 MN (Tensile), 4 MN (compressive) acting along length, breadth & thickness directions respectively. Find the change in volume. Take E as 200GPa & poisson’s ratio 0.25. Also find the change in Length, breadth & thickness. Also find the change that can be made in the4 MN load, in order that there should be no change in volume.
A steel bar having 65mm*65mm*3000mm dimension is subjected to an axial force of 128 kN. Taking E=2*105N/mm2 and m = 0.3, find out Change in dimensions (height, width and length), Change in volume and Volumetric Strain
The recessed composite beam in the figure is made of steel and aluminum It was produced and a force of 20 kN was applied to its tip. According to what is given, the maximum amount of steel and aluminum Find the stresses. (Eç = 200 GPa, EAl = 80 GPa) dimensions in mm
3. A rectangular solid bar of width 20mm and depth 35mm is subject to a pure positive moment of 450Nm. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line. 4. The bar in Q3 is also subject to a tensile load of 15kN applied at the centroid of area. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line.
4. The general stress element is loaded such that ơx = 30 MPa, oy = -20 MPa, Txy = 5 MPa. Using Mohr's circle, find out the maximum normal stress and shear stress acting on this element. 5. The general stress element is loaded such that ơ, = 50 MPa. Using Mohr's circle, find out the maximum normal stress and shear stress acting on this element. (Simple tension)
Q1/ Find max tension & compression stresses for part BC for beam shown in figure below. 20 KN 20 KN 2 cm 2 cm B 10 cm A D 2 cm 30 cm 50 cm 30 cm 10 cm Q2/ Find diagram for shear force and moment of EFGH beam as shown in figure below. 20 KN 3 A 4 400 cm 400 cm 400 cm 400 cm H 'F 400 cm B 28 KN