5. A sheet of BcC iron 1 mm thick was exposed to a carburizing gas atmosphere on one side and a decarburizing atmosphere on the other side at 725 °C. After reaching steady state , the iron was quickly cooled to room temperature The carbon concentrations at the two surfaces of the sheet were determined to be 0.012 and 0.0075 wt %. Compute the diffusion coefficient if the diffusion flux is 1.5 x 10 -8 kg/ m2 · s. The density for carbon and iron is 2.25 and 7.87 g/cm 2, respectively

5. A sheet of BcC iron 1 mm thick was exposed to a carburizing gas atmosphere on one side and a decarburizing atmosphere on the other side at 725 °C. After reaching steady state , the iron was quickly cooled to room temperature The carbon concentrations at the two surfaces of the sheet were determined to be 0.012 and 0.0075 wt %. Compute the diffusion coefficient if the diffusion flux is 1.5 x 10 -8 kg/ m2 · s. The density for carbon and iron is 2.25 and 7.87 g/cm 2, respectively

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A small piece of Fe-0.4 wt%C alloy is held at 728 °C for 1 hour and then quenched. On microstructure analysis the microstructure had some level of martensite in it. Estimate the weight fraction of martensite to 2 d.p. Answer:
5) In the adsorption of N2 at 90.1 K on a certain solid, the following volumes of gas, reduced to standard condition, were found to be adsorbed per gram of the solid at the indicated relative pressures. Determine: a) the BET constants b) E, and E c) identify the type of isotherm P/po 0.05 0.10 0.15 0.20 0.25 V, cm³ 51.3 58.8 64.0 68.9 74.2
7.10 A simple cubic (a = 0.3 nm) substrate has been cut along the (100) at a 3° angle to create a stepped surface. If homoepitaxial growth is attempted at 600 °C, will the diffusion length be greater than the distance between steps? Use AG des = 1.0 eV/atom, AGS = 0.5 eV/atom, and vs = 1013/s.
Please describe the function of Gas Diffusion Layer and Bipolar plate in fuel cell stack.
any help with this question would be amazing
3. In a chronoamperometric experiment the following data are obtained for the reduction of a species whose bulk concentration is 1x103 M and diffusion coefficient is 1x10 cm/sec. (Double layer charging corrections have been made) What information can you derive? State any assumptions made. t(sec.) i(uA) 0.01 164 0.02 0.04 116.1 82.3 0.06 74.14 0.09 71.6 0.16 62.25 0.40 42.2 1.00 34 2.00 24.2 3.00 20.0
The following table gives the volume of nitrogen (reduced to 0°C and 1 bar) adsorbed per gram of active carbon at 0°C at a series of pressures: 1731 P/Pa v/(cm³ g-¹) 524 0.987 3.04 3058 C. 29 cc/g D. 23 cc/g E. None of the choices 5.08 4534 7.04 Determine the volume required to form a monolayer. A. 34 cc/g B. 40 cc/g 7497 10.31
3. At 273 K and 105 Pa, the value of n for He is 1.88 x 10-5 Pa s. Calculate ii. The collision diameter. ii. The diffusion coefficient.
v/mVs ip.a/μA Cyclic voltammetry of ferrocene monocarboxylic acid (FMCA) on 7x10³ um diameter glassy carbon disc working electrode at 25°C showed reversible electrochemistry at all the potential scan rates v, studied. The data for the peak anodic current, ipa are tabulated. If the sytem is a one-electron process with a diffusion coefficient, D, value of 5.2x10 cm's, determine the concentration of FMCA 10 5.00 50 15.00 100 22.75 200 34.50 500 58.25 1000 84.50
Carburizing is a process by which the surface (1) concentration of a ferrous alloy is (2) by diffusion from the surrounding environment at high temperatures. (1) = oxygen, (2) = increased. (1) = carbon, (2) = increased. O (1) = oxygen, (2) = decreased. (1) = carbon, (2) = decreased. %3D
3. Two molecules, A and B, with concentrations of 1.00 mM are studied at a glassy carbon electrode at 100 mV/sec. Each species undergoes a one-electron reduction. The diffusion coefficient for A is 64.2 x 10-6 cm²/s, while B has a diffusion coefficient of 4.16 x 10“ cm²/s. Briefly explain how the peak height of the reduction wave will differ between molecules A and B.
What is the difference between effect of pH and Point of zero charge with regards to Adsorption