5. A plinth with a shape of a frustum of a cone is made of a melted CHB or Concrete hollow blocksand form into a plinth. It has a specific weight of 4.42 metric slug/ft with a specific gravity of 3.Assuming it is at rest find the average normal stress acting in the mid-height of the plinth in psi.r= 304.8 mmR = 457.2 mmMid-height= 1219.2 mmh = 2438.4 mmH

Question is based on plinth made up concrete hollow blocks with shape of frustum of cone . Specific…

5. A plinth with a shape of a frustum of a cone is made of a melted CHB or Concrete hollow block and form into a plinth. It has a specific weight of 4.42 metric slug/ft³ with a specific gravity of 3 Assuming it is at rest find the average normal stress acting in the mid-height of the plinth in ps r = 304.8 mm R = 457.2 mm Mid-height = 1219.2 mm %3D h = 2438.4 mm H

5. A plinth with a shape of a frustum of a cone is made of a melted CHB or Concrete hollow block and form into a plinth. It has a specific weight of 4.42 metric slug/ft³ with a specific gravity of 3 Assuming it is at rest find the average normal stress acting in the mid-height of the plinth in ps r = 304.8 mm R = 457.2 mm Mid-height = 1219.2 mm %3D h = 2438.4 mm H

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question: What is the effective vertical stress at Point A? Ym = 109 pcf 12 ft Layer 1 Ysat = 111 pcf 3 ft Ysat = 113 pcf 5 ft Layer 2 Not to scale O 1707 psf 2010 psf 2206 psf
please solve and exlain in neat hand writing
I need the answer quickly
0.10
Given data: Maximum principal stress-38 MPa Minimum principal stress=32.5 Mpa Find maximum shear stress
Someone can help me on this one. Thanks
A rectangular column of sides 0.4 m × 0.35 m , made of concrete, is used to support a compressive load of 2800 kN. Four steel rods of each 24 mm diameter are passing through the concrete as shown in figure. If the length of the column is 3 m, Esteel=200 GPaEconcreate=29 GPa a)determine the normal stress in the concrete b)determine the normal stress in the steel.
Example: Determine the nominal eccentric compressive strength Pa and the eccentricity e corresponding to the tension controlled strain limit (E, = 0.005). Use f = 3000 psi and fy = %3D !! 50,000 psi. Layer 1 Layer 2 6 #8 bars 15 in 2.4 in 2.4 in 24 in 0,003 21.6 in 2,4 Es1=E=0.005 C.
2. The following square section is subjected to an unsymmetric bending moment M=850 Nm, as shown. Compute the stresses at each of the 4 outer corners of the section, and sketch a 3D distribution of the stresses 2 B M=850 Nm mm 260 E 25 A D 250 mm REQ'D - stress at each corner - 3D stress distribution
Please recheck your answer
Given the state of stress shown, determine the normal stress (in MPa) acting on the inclined plane a-a if S = 74.2 MPa, N = 49.64 MPa, and A = 38.2°. Express final answer in four decimal places. N X A° S
please recheck your final answer.