5- Y=10 kN/m' and Teable=2.76 kN Determine the placed distance of the each cables along the length of trough Waterine Cable Trough d-? Hinge A-A (8.75+ cable

Q: = constant 5. Bernou lli's equation is expressed as asY'2g Research on the corresponding units por…

A:

Q: Determine the force P to move block B. SHOW COMPLETE SOLUTION AND ILLUSTRATION FINAL ANSWER IN 3…

A:

Q: 1 2. +tanz= tan z sin z cos z

A:

Q: Only answer A. Explain why the obtained answer makes sense.

A: This question is related to the Strength of the material from Civil Engineering. As per question…

Q: The uniform wire is bent into the shape shown and held by the frictionless pin at O. Determine the…

A: It is given that,

Q: - A uniform beam (EI= constant) PQ in the form of a quarter-circle of radius R is fixed at end P and…

A:

Q: I need detailed help solving (2), please.

A: Ans page 1:Ans page 2:Ans page 3:

Q: Q R S LU M H. `A E F G H P1 P1 P2 P2 P2 P1 L2 L2

A:

Q: 1. Express the two forces shown as Cartesian vectors. 2. Determine the magnitude and coordinate…

A: Given:- The magnitude of the force along with AB = FAB = 200 N  The magnitude of the force along…

Q: State whether the equation is ordinary or partial, linear or nonlinear and determine its order and…

A: To verify that y is a solution of a differential equation, substitute y in the given differential…

Q: 3 d²y dx² dy -2 -8y = 0 dx

A:

Q: QUESTION 2 PROBLEM 2: Calculate the components of the forces at B and C. A D E F b Given: P= 21 kN a…

A:

Q: A beam is subjected to equal bending moments of M₂ = 35 kip-ft. The cross-sectional dimensions are…

A:

Q: J L M O N JKLMNO is an irregular hexagon. If JK = 5 m, MN = 2 m, NO = 12 m, and JO = 8 m, then 3.…

A:

Q: B C 8466.8 N A D 1 m 1 m E 1m F 5184.6 N 0.75 m

A:

Q: Problem 1 The horizontal rigid beam holds the distributed load indicated in the picture. Determine…

A: Area of each bar, Modulus of elasticity,

Q: The degree of homogeneity of the function f(x, y) = (x² - 4y²)-¹/2 O A. 1 OB.-1 O C. -1/2 O D. None…

A:

Q: Hiw:-solve the Tivensystemof equation by Cramer Rule 1- X + Xz = 4 2X,-Xz= Z %3D

A: X1 = 2X2 = 2explanation is given in below step

Q: Determine the slope at the tip of a cantilever beam, loaded by a uniform distributed load over its…

A: Solution:

Q: use of beam elements.

A: Beam elements are 2D members used in Finite element analysis. The beam elements are efficiently…

Q: d²u du What is the order of +t dt2 + 3u = 1? A. Order 1 B. Order 2 C. none Answer:

A: To find :- order of given differential equation

Q: Describe about the typical Foundation Wall Problems and Related Causes? In detail.

A: Some typical foundation wall problems are given as, Horizontal failure: The first sign of…

Q: Q5. What is the minimum clearance required by OSHA regulations between a crane and a 150-kV power…

A: The Occupational Safety and Health Administration(OSHA)-The Occupational Safety and Health…

Q: Determine the slope at Point D for the beam shown. EI is constant

A:

Q: A. Solve the following system of equations by Gauss elimination method. [2 1 1 27 4 0 2 1x2 4. 3 2 2…

A: In Gauss elimination method we  make an augmented matrix [ A : B] and the elements of A below the…

Q: (1²+ x²) dt + (2tx – x) dx=0

A:

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A: Solving question AFig is Giventhere is horizontal line symmetry for the handlesno line of symmetry…

Q: Part A: Draw the Free Body Diagram of the system with the distributed load. Part B: Find the…

A:

Q: Determine whether the limit exists. If so, find its value. If the limit does not exist, indicate…

A: Given:- To find:- value of limit

Q: یا #I A A 3m 600 | 3m B 4m D 3m 5m B, C, and I are pin connected Note: E to C is one member (…

A:

Q: Below presents a continuous beam with A being fixed and B is pinned and C has a roller. Take: E =…

A:

Q: Force Method is also know as Method of Answer Displacement

A: methods of analysis of indeterminate structure is  done by following methods - 1) Force method /…

Q: Verify whether the following are valid potential functions: (i) ¢ = 4r²– 5y² (1) 0 = 2r + 5y

A:

Q: How is the elastic curve obtained? please give calculation for elastic curve as well. Take EI as…

A: Required: Explanation for the drawing of elastic curve

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.