Note: Unit weight of the beam and girder is neglected 2) The floor Sygstem of aresistingtwo steel girders. The5- in- thick reieforcedsupported bybuilding Consists of aConcrete slabfour steel floor beams, whichonarecross- Secti onalareas of the floor beoms and thegirders14-7 in' and 523 in?, res pectively. Determine the dead loodsareacting onthebeam sCG and DH and hegir der AD.Use Ye = 23.6 kN/m3GirderBBEAMS24 ftlo ftl0 ftlo fH

Girder is normally a beam that supports other small size beams and moves through the horizontal…

5- in- thick reinforced The floor System of Concrete slab resisting two steel girders. The building Consists of a four steel floor beoms, which are supported by on cross- Sectional areas of the floor beoms and the girders 14-7 in and 523 in?, res pectively. Determine the dead loods are acting on the beams CG and DH and the gir der AD. Use Ye = 23.6 kN/m3 Girder BEAMS 24 ft

5- in- thick reinforced The floor System of Concrete slab resisting two steel girders. The building Consists of a four steel floor beoms, which are supported by on cross- Sectional areas of the floor beoms and the girders 14-7 in and 523 in?, res pectively. Determine the dead loods are acting on the beams CG and DH and the gir der AD. Use Ye = 23.6 kN/m3 Girder BEAMS 24 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the truss shown in (Egure 1). Suppose that F-60 kN and F₂-25 kN Figure 40 KN Part C Fau 50 AN Submit -2m- D 15m 1of1 > 15m 15m μA Value -F₂ Part A Request Answer Determine the force in member ED of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HA FED Value Submit Part B Request A Determine the force in member EH of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Submit Fon- Value Determine the force in member GH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of…
4) The beam shown is under simple tension and has a circular section. What are the normal stresses at the four points (a, b, c and d) of the section shown? F Área transversal-A #F
2. Calculate the internal forces in the bar GF and GD in a roof truss as shownbelow. For each bar, indicate if the internal force is tensile or compressive. Usethe section method (snittmetoden). Point A has simple support and D has rollersupport.
PLEASE SHOW COMPLETE SOLUTION. THANKS Determine the force in members GE, GC, and BC of the truss shown. Indicate whether the members are in tension or compression. Use method of sections.
If beam BEH is hinged at the columns B, E, and H, determine its degree of indeterminacy.
Find 5 internal forces of the truss members, Also Find all zero force member. Thank you.
round off final answer to 4 decimal places
Consider the 21-member truss shown; determine the zero-force members and force in each member then state if they are in tension or compression.(Support on point B and C are pinned and roller, respectively)
PLEASE ANSWER ASAP THANKS
Determine the force in each member of the truss shown by the method of joints. Show free body diagram and handwritten solution. Please make sure it is correct answer. Thank you!
Determine the smallest safe cross-sectional areas of members CD, CI and CHfor the truss shown. The allowablestress are 100 MPa in tension and 80 MPa in compression. Indicate tension or compression.(Draw the required FBD and answer in ??2).