5 For measuring a wire of thickness 1mm, out of a ruler, vernier calipers and Micrometer which one will be more accurate and which one will be less accurate?

Q: On the toleranced rectangle below, what is the tolerance within which the to be parallel to the…

A: Parallel symbol describes a parallel orientation of one reference feature to a datum surface or the…

Q: In order for a certain refrigerator door to close tightly, the refrigerator must beleveled up 0.24…

A: Given data as per question Total thickness = 0.24 in The thickness of lower shim =0.097 in

Q: What is term ‘clearance’ in connection to measurement?

A:

Q: If the main scale reading(mm) and vernier scale reading (division) are 11 and 15 respectively for a…

A: main scale reading = (MSR) = 11 mm vernier scale reading (VSR) = 15 mm no of division = 20

Q: ?What is the final reading of Vernier caliper from the figure given below 10 30 40 50 20

A: The main scale reading =5mm Vernier scale reading=0.775mm

Q: Q1 (a) During construction of a highway bridge, the main girders as shown in Figure Q1(a) are…

A: The maximum bending stress in a girder due to this load is 85 MPa.

Q: 6. What is accuracy in measurement?

A: Measurement:  It is the numerical quantification of the attributes for a body that are used to…

Q: With appropriate precision (significant digits), what is 2 + 2.1?.

A: It is required to determine 2+2.1

Q: Circle all correct statements. Plastic deformation a. Is permanent. b. Is recoverable. c. Can be…

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: Q3) A student wants to know the linear measurements of a screw thread (in inch), if the student…

A: (A) The thread angle is 55o (B) The screw type is the "Whitworth screw"

Q: The force developed in the brake cylinder is 2.74 KN and the diameter of the cylinder is 4.5 cm. If…

A: Option d is correct

Q: A pneumatic system is producing 50 lb/in.2 of gauge pressure. A cylinder is needed to press an…

A: The force produced by the pneumatic cylinder can be calculated using the formula: Force = Pressure x…

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: A slip gauge setting height 53.155 mm is observed when a sine bar of the length 127 mm is used…

A: Angle using sine bar and slip gauge is find out by Angle = Sin-1(slip gauge height/ length of sine…

Q: 1. Is there a difference between the values of Qideal calculated by equation (7) and Qact by using…

A: given:

Q: ZPQ'R= = LPQ'R= = MI i O rad

A:

Q: among the ruler and vernier caliper gave the least % err

A: Ruler and vernier caliper both are measuring devices.

Q: f the metric micrometer to a precision

A: 5.332

Q: What is the minimum distance from the holes at each end of the part? - 2x Ø 1.375-1.390 +Ø010 LABC…

A:

Q: The smallest division on the main scale of Vernier calipers is 0.1 cm. Ten divisions of the Vernier…

A:

Q: The motor produces 30kW to the A-36 steel solid shaft at a frequency of 20HZ. The shaft is 70mm in…

A: Given data as per question diameter of shaft (d)=70 mmω=20 Hz=20×6.28=125.6 radsPower developed by…

Q: The found that the dial indicator reading was increasing wi moving in a horizontal line along the…

A: We have to decide what gauge is required next.

Q: You are given a set slip gauge containing 46 pieces of 2mm base (M46/2). Show how you would build…

A:

Q: The least count of  a  micrometer is a. 0.01 mm b. 0.2 mm c. 0.05mm d. 0.1mm

A: Option a is correct.

Q: An engineer is using a machine to cut a flat square of Aerogel of area 144 sq. c.m. If there is a…

A:

Q: what would be the the tensile strenght in pounds per square inch of a specimen measuring 0.375 in.…

A:

Q: The assembly consists of a 3-kg vertical pulley A and a 14 horizontal pulley B. If a 2-kg block is…

A: Given data: m=3 kgM=14 kgr=30 mmR=100 mmh=0.1 m Need to determine the speed of pulley B.

Q: igh precision in angular measurements can be made using a sine bar. For using a 200 mm sine bar to…

A: Given:Length of sine bar, L=200 mmangle=49o 20'angle=49+2060=49.33oDiameter of rolls, d=35 mm

Q: A slip gauge setting height 50.14 mm is observed when a sine bar of the length 147.32 mm is used…

A: Slip gauge angle

Q: I want to buy a two METAL SPUR GEAR for my 2 pieces of G.I pipe with an 3 inches diameter (3mm…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Section B uses a…

A: Question 1:Solution - Yes, Central line divides the the section symmetrically. It ease the…

Q: dimension the distance between the holes

A: Bilateral tolerance B = 1.625T = 0.006Bilateral tolerance means that the dimension can vary in both…

Q: A micrometre is a precision measuring instrument, with 50 division on the thimble. Select one: True…

A: A micrometre is a precision measuring instrument, with 50 division on the thimble. Select one: True…

Q: suring plan What is the difference between feature How do you measure cylinders C1 or C2

A: Inteoduction we utilize a direction framework to depict the developments of an estimating machine.…

Q: Read the following millimetric vernier caliper setting 005mm Answer with units:

A: Vernier caliper reading = reading of main scale + reading of other scale (where the two lines are…

Q: The advantage of Vernier caliper over Micrometer is Select one: a. Both devices not useful b. Not…

A: vernier calipers is used to measure inner, outer dimensions and depth can also be measured.

Q: I would be more accurate to say it is 1.25 cm long. This measurement 1.0 1.5 cm 1.1 1.2 1.31.4 has 3…

A: Based on the given measurement, it is clear that the pointer lies between 1.2 and 1.3 cm.

Q: The term "Allowance" in limits and fits is usually referred to 1. Minimum clearance between shaft…

A: Allowance :- (A) Minimum clearance between the shaft and hole The minimum clearance in a shaft and…

Q: Determine the x, y, z components of reaction at the journal bearing C if 0 = 0°.

A:

Q: What other geometric tolerance is automatically controlled when parallelism is applied to a surface?…

A: Geometric tolerance is a system that is used for the physical understanding of the design. It…

Q: What tolerance is specified for the width of the groove?

A: Given :-   Bolt Drawing   Find :-  Tolerance of the width of the drawing

Q: When the total indicator reading or movement (TIR or TIM) of the dials shown in Figures (a &b) are…

A: The tolerances are measured with the help of a Total indicator reading(TIR) especially  for the…

Q: To which of the following geometric tolerance families does perpendicularly belong?     Form…

A: Orientation tolerance are used to determine the orientation with respect to reference i.e  an datum…

Q: f the main scale reading (mm) and vernier scale reading (division) are 36 and 4 respectively for a…

A: Vernier caliper is device used to measure the length dimension.

Q: Would a flatness tolerance of .010 for the part in the drawing below be appropriate? 3.000 1.000 XXX…

A: Calculate the maximum measurement of height. hmax=1+0.005=1.005