5) Benzene at 20°C has a viscosity of 0.000651 Pa-s. What shear stress is required to deform this fluid at a strain rate of 4900 s-1 ?

Q: Fluid mechanics question Solve and please provide correct answers An oil of viscosity 0.02 Ns/m2 is…

A:

Q: A fluid at 20°C has a viscosity of 0.007 Poise. What shear stress in Pa is required to deform this…

A: Given: strain rate = 294000/min Viscosity = 0.007 poise

Q: 1)The model of the torpedo (a military vehicle that goes very fast underwater) as placed in a tank…

A: To obtain the solution of the 1st part of the question, we will apply the Froude model law, which is…

Q: (b) Use the above expression of the velocity to determine the expression of the torque (I) required…

A:

Q: 2- Velocity distribution of fluid over a flat plate is given by: U = % y - y in which (u) velocity…

A:

Q: The velocity profile for the course of a Newtonian substance between two wide, parallel plates is…

A:

Q: 8- If a liquid has an amount of viscosity (0.0048 poise) Calculate the sternum of the sternum…

A: Fluid Machinery

Q: With free body diagram. Clear and complete solution please thank you.  1. A square block weighing…

A:

Q: The apparatus shown in the figure is to coat a thin steel plate with oil. using for. Fluid1 has a…

A:

Q: What is the shear force that acts on the circumference of the piston (N)?

A:

Q: If the viscosity of the fluid increases as the shear rate increases, O a. The fluid is shear…

A: It is required to choose correct option

Q: 1. 3- 4- polymer fluid has the data in the table blow. Sketch the relationship between shear stress…

A:

Q: Determine the dynamic viscosity (Pa-sec) and kinematic viscosi ty (m2/s) of vater with a specific…

A:

Q: 3. 2. The velocity distribution for flow over a fl velocity in metre per second at a distance y m…

A:

Q: At a point in a flowing fluid, the shear stress is 3x10-4 psi and the velocity gradient is 1 s-1.…

A:

Q: Explain shear stress, strain rate, internal friction. Discuss the profile of viscosity for gases…

A: Shear Stress :- Shear force acting on area under shear is known as Shear stress.  Strain Rate :-…

Q: Write general relationship between shear stress ? and rate of deformation du/dy for non-Newtonian…

A: The relationship between the shear stress and rate of deformation for Non-Newtonian fluid is written…

Q: A square block has 320 mm bottom sides dimensions, weighing W is 1.4 kN on an edge slides down an…

A: Given data: The bottom side, a = 320 mm. The weight of the block, W = 1.4 kN. The incline angle,…

Q: A hydrodynamic journal bearing is subject to 2000 N load at a rotational speed of 2000 rpm Both…

A:

Q: Two parallel flat plates are spaced 2 in. apart. One plate is moving at a velocity of 10 ft/min and…

A:

Q: pus... A rectangular block weighing, W kN and having an edge measuring L mm is sliding down on an…

A: Solution: To find: The terminal velocity of the block in the given conditions.   Terminal velocity…

Q: Determine the kinematic viscosity in stoke if the shear tension at a spot in oil with a density of…

A:

Q: A piston with a diameter of 0.8 m and width of L=0.1 m rotates with 6 rad/s inside a cylinder that…

A: The given data are: L=0.1 mω=6 rad/sd=0.8 mD=1 mμ=8×10-3 N.s/m2

Q: With free body diagram please thank you. Clear and complete solution please. 1. A square block…

A: Given Data- Weight W=1.1KN Side lenght a=250mm Thickness of film =6μm Viscosity=7mPa-s We have to…

Q: A chamber wall (1m x 2m) has an inside temperature of -4°C. The outside temperature is 22°C. The…

A: Given:Area of the wall, A=1m*2m=2 m2Inside temperature, Ti=-4oCOutside temperature, To=22oCThickness…

Q: Falling Sphere Viscometer Given:             Inner diameter of cylindrical tube = 0.03 m…

A:

Q: Question 1. The apparatus shown in the figure is used to coat a thin steel plate with oil. Fluid1 is…

A:

Q: A shaft of diameter 74.90mm rotates in a bearing of diameter 75.03mm and of 75mm length. The annular…

A:

Q: A tape, of width w = 25.40 mm is to be coated on both sides with a lubricant by drawing in through a…

A: Given data  width of tape (w) = 25.40 mm c = 0.3 mm t = 0.381 mm L = 20 mm μ = 1.0054 Kg/m-s Fmax =…

Q: The viscosity of a fluid is to be measured by a viscometer constructed of two 30-cm-long concentric…

A: First write the torque expression,

Q: Determine the kinematic viscosity oil having the relative density as 0. shear stress at a point in…

A: Given data as per question  Relative density of oil=0.86. The shear stress at a point in oil ,…

Q: According to Newton’s law of Viscosity, shear stress is inversely proportional to the velocity…

A: According to Newton’s law of Viscosity, shear stress is inversely proportional to the velocity…

Q: A thin plate of very large area is placed in a gap of height h with oils of Example viscosities µ'…

A:

Q: In order to determine the viscosity of a Newtonian fluid, you conducted an experiment at 20°C . The…

A: Solution:

Q: Q1:- A 300 mm diameter of pipes and 350 mm long slides along a large diameter cylinder at a speed of…

A:

Q: A bar with a circular section of diameter D1=218 mm moves axially inside a bearing with diameter…

A: Given data: D1=218 mmD2=223 mmL=0.5 mμ=30x10-3 Pa.sV=0.9 m/s Need to determine the value of F needed…

Q: Q A thick-walled cylinder has an inside diameter of 150mm. The inside of the cylinder is subjected…

A: Soln:-  d1 = 150 mm             r1= 75 mm               P1= 350 bar = 350 × 10^5 pa           Max.…

Q: hydrodynamic journal bearing is subject to 2000 N load at a rotational speed of 2000 rpm Both…

A: Given:Rotational speed of bearing, N=2000 rpmLoad on bearing, P=2000 NDiameter, d=40 mm or 0.040…

Q: A steel tape 0.5 mm thick and 20 mm wide is pulled by a force F through a slit opening 1.5 mm and…

A: Given data: The thickness of the tape, t = 0.5 mm. The width of the tape, w = 20 mm. The slit…

Q: n = Xe)r -Equation 1 vhere X = 1.7419 and (E/R) = -0.018 are constants for a given fluid. You are…

A: According to the given question, the velocity varies with temperature. But in actual practice, it…

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.